LG 32LC7D Series - APPENDIX; Input and Picture Adjustment Commands

01. Power (Command2:a)
To control Power On/Off of the TV.
TransmlsSiOn[k] [a] [] [Set !D][] [Data] [Cr] .............
Data 0 : Power Off Data I : Power On
AcknOwledgement [a][] [Set ID] [ ] [OKiNG] [Data] [x]
* In a like manner, if other functions transmit 'FF' data
based on this format, Acknowledgement data feedback
presents status about each function.
02. Input Select (Command2:b)
To select input source for the TV.
TransmlSSiOn[k] [b][] [Set ID] [ ][Data] [Cr]
Data 0: Digital
Data 1: Analogue
Data 2:AV1
Data 3:AV2
Data 4: Component 1
Data 5: Component 2
Data 6: RGB-PC
Data 7: HDMI1/DVI
Data 8:HDMI2
AcknOwledgement [b][ ][set ID][ ][OKiNG] [Data] [x]
03. Aspect Ratio (Command2:c)
To adjust the screen format.
You can also adjust the screen format using the ARC
button on remote control or in the Special menu.
Transmission [k] [C][] [Set ID][] [Data] [cr]
Date 0: Auto
1: 4:3
2:16:9
3:14:9 (-10) - D: 14:9 (0) - 17:14:9 (10)
18: Zoom (-16) _ 28: Zoom (0) _ 38: Zoom (16)
39: Cinema Zoom (1) - 48: Cinema Zoom (16)
ACknOwledgement [c] [] [Set ID] [] [OK/NG] [Data] [x]
Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
04. Screen Mute (Command2:d)
To select screen mute on/off.
TransmiSsion [k] [d] [][set ID] [] [Data] [Cr]
Data 0 : Screen mute off (Picture on)
Data 1 : Screen mute on (Picture off)
ACknowledgement [d][ ][Set ID][ ][OK/NG] [Data] [x]
OS. Volume Mute (Command2:e)
To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission [k] [e][] [Set ID][] [Data] [Cr]
Data 0 : Volume mute on (Volume off)
Data 1 : Volume mute off (Volume on)
AcknOwledgement[e][ ][Set ID][ ][OK/NG] [Data] [X]
06.
Volume Control (Command2:f)
To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k] [f] [] [Set ID] [ ] [Data] [Cr]
Data Min : 0 _ Max : 64
Refer to 'Real data mapping1 ' as shown below.
Acknowledgement[f] [] [Set ID] [ ] [OK/NG] [Data] [x]
07.
Contrast (Command2:g)
To adjust screen contrast.
You can also adjust contrast in the Picture menu.
TranSmiSsiOn[k] [g][ ][set ID][ ][Data] [Cr]
Data Min : 0 - Max : 64
Refer to 'Real data mapping1 ' as shown below.
Acknowledgement [g][ ][Set ID][ ][0K/NG] [Data] [x]
08.
Brightness (Command2:h)
To adjust screen brightness.
You can also adjust brightness in the Picture menu.
Transmission[k] [h][] [Set ID][] [Data] [Cr]
Data Min : 0 _ Max : 64(*transmit by Hexadecimal code)
Refer to 'Real data mapping1 ' as shown below.
Acknowledgement[h][ ][set ID][ ] [OK/NC] [Data] [x]
09.
Colour (Command2:i)
To adjust the screen colour.
You can also adjust colour in the Picture menu.
TransmiSsiOn [k] [i][ ][set ID][ ][Data] [cr]
Data Min : 0 _ Max : 64
Refer to 'Real data mapping1 ' as shown below.
Acknowledgement [i] [ ] [set ID] [ ][OK/NG] [Data] [x]
*Real data mapping 1
0 : Step 0
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100
Tint: R50 _ G50, Balance: L50 _ R50
r'_
Z
C7
X
93