Lilytech ZL-7802D - Operation; Set setpoints; Parameter code table

Suzhou Lily Tech. Co., Ltd.
Page 2. Total 5 pages
Operation
Set setpoints
Keep〖S〗depressed for 3 seconds. Display , and temperature setpoint (“t” + “setpoint”).
Press〖S〗to switch between temperature set status and humidity set status (“H” + “setpoint”).
Press〖▲〗or〖▼〗to set the setpoint (keeping depressed could fast set).
Keep〖S〗depressed for 3 seconds to save the settings, and exit.
The setting status will exit if there is no key operation for 30 seconds, and the settings will not be saved.
Factory setpoints are 38.0℃ and 60.0%RH.
Parameter code table
Code
Function
Range
Remark
Factory
set
U10
Temperature setpoint up limit
U11 ~ 99.9℃
99.9
U11
Temperature setpoint low limit
-40.0℃~ U10
-40.0
U12
High temp. protection start point
0.1 ~ 10.0℃
Relative value, real value = setpoint + U12
0.3
U13
High temp. protection stop point
0.1 ~ 10.0℃
Relative value, real value = setpoint + U13
0.1
U14
Low temperature alarm point
0.0 ~ 99.9℃
Relative value, real value = setpoint – U14
35.0
U15
High temperature alarm point
2.0 ~ 99.9℃
Relative value, real value = setpoint + U15
99.9
U16
Temperature hysteresis
0.0 ~ 20.0℃
Effective when U73 = 1
0.2
U30
Temperature calibration
-20.0 ~ 20.0℃
0.0
U40
Timer R1 on time unit
0 ~ 2
0: sec, 1: min., 2: hour
0
U41
Timer R1 on time
1 ~ 999
120
U42
Timer R1 off time unit
0 ~ 2
0: sec, 1: min., 2: hour
1
U43
Timer R1 off time
1 ~ 999
120
U46
Output R1 working mode
0 ~ 3
0: Timer output
1: High temperature/humidity protection
2: Timer output + High temp./humi. protection
3: Disable
2
U47
R1/R2 work during auto tuning
0 ~ 1
0: R1/R2 keep working during auto tuning
1: R1/R2 keep off during auto tuning
1
U50
Humidity hysteresis
0.1 ~ 20%RH
2.0
U51
R2 delay protection time
2 ~ 300 sec.
5
U52
Humidity calibration
-20.0 ~ 20.0%RH
0.0
U53
High humidity protection start point
1.0 ~ 20.0%RH
Relative value, real value = setpoint + U53
5.0
U54
High humidity protection stop point
0.0 ~ 20.0%RH
Relative value, real value = setpoint + U54
0.0
U55
Low humidity alarm point
0.0 ~ 99.9%RH
Relative value, real value = setpoint – U55
0.0: disable the alarm function
20.0
U56
High humidity alarm point
0.0 ~ 99.9%RH
Relative value, real value = setpoint + U56
0.0: disable the alarm function
30.0
U60
Egg turn times set
0 ~ 999
0: do not counter the times of egg turn
0
U61
Left turn R3 time unit
0 ~ 2
0: sec, 1: min., 2: hour
1
U62
Left turn R3 time
1 ~ 999
90
U63
Right turn R4 time unit
0 ~ 2
0: sec, 1: min., 2: hour
1
U64
Right turn R4 time
1 ~ 999
90
U66
Reset egg turn counter after power supplied
0 ~ 1
0: reset, 1: not reset (keeps)
0
U67
Egg turn period time saving
0 ~ 1
0: not save, 1: save
0
U68
Reset incubated days counter after power supplied
0 ~ 1
0: reset, 1: not reset (keeps)
1
U69
Max incubation days set
0 ~ 999 day
0: do not counter the days of incubation
30
U70
External digital input working mode
0 ~ 2
0: disable, 1: alarm if short 2: alarm if open
0
U71
Beep alarming
0 ~ 1
0: disable, 1: enable
1
U73
Temperature control mode
0 ~ 1
0: PID, 1: on/off control
0
U74
Heater power during PID auto tuning
10 ~ 100%
Percent of heater’s whole power rate
50
P
Proportion parameter: Kp
0.1 ~ 9999
2.6
I
Integration parameter: Ti
0 ~ 9999
500
d
Differential parameter: Td
0 ~ 9999
50
U99
Password
000 ~ 999
000: disable password
000