EasyManuals Logo

Lincoln Electric MIG-PAK 10 User Manual

Lincoln Electric MIG-PAK 10
64 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
MMIIGG--PPAAKK 1100
IM551-C
May, 2002
22801 St. Clair Ave. Cleveland, Ohio 44117-1199 U.S.A.
Tel. 216.481.8100
WEB SITE: www.lincolnelectric.com
Safety Depends on You
Lincoln arc welding and cutting equipment is designed and
built with safety in mind. However, your overall safety can be
increased by proper installation ... and thoughtful operation
on your part. DO NOT INSTALL, OPERATE OR REPAIR
THIS EQUIPMENT WITHOUT READING THIS MANUAL
AND THE SAFETY PRECAUTIONS CONTAINED
THROUGHOUT. And, most importantly, think before you act
and be careful.
OPERATOR’S MANUAL
MANUAL DE OPERACIÓN
MANUEL DE L’OPÉRATEUR
La Seguridad Depende de Usted
Los equipos de corte y soldadura al arco Lincoln han sido
diseñados y construidos teniendo en cuenta su seguridad.
No obstante, ésta se verá incrementada si la instalación se
realiza correctamente, y si pone atención en el manejo de
los mismos. NO INSTALE, UTILICE O REPARE ESTE
EQUIPO SIN ANTES HABER LEIDO ESTE MANUAL Y LAS
MEDIDAS DE SEGURIDAD QUE CONTIENE. Y, lo más
importante, piense antes de actuar, y tenga mucho cuidado.
La sécurité dépend de vous
Le matériel de soudage et de coupage à l'arc Lincoln est
conçu et construit en tenant compte de la sécurité. Toutefois,
la sécurité en général peut être accrue grâce à une bonne
installation... et à la plus grande prudence de votre part. NE
PAS INSTALLER, UTILISER OU RÉPARER CE MATÉRIEL
SANS AVOIR LU CE MANUEL ET LES MESURES DE
SÉCURITÉ QU'IL CONTIENT. Et, par dessus tout,
réfléchissez avant d'agir et exercez la plus grande prudence.
TABLE OF CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Technical Specification . . . . . . . . . . . . . . . . . . . . .9
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Learn to Weld . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .54
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . .56
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
TABLA DE CONTENIDO
Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Especificaciones Técnicas . . . . . . . . . . . . . . . . . . . .9
Instalación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Operación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Aprendiendo a Soldar . . . . . . . . . . . . . . . . . . . . . . .29
Accesorios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Localización de averías . . . . . . . . . . . . . . . . . . . . . .54
Diagramas de cableado . . . . . . . . . . . . . . . . . . . . . .56
Partes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
TABLE DES MATIÈRES
Sécurité....................................................................2
Introduction ..............................................................8
Fiche technique .......................................................9
Installation ...............................................................10
Fonctionnement .......................................................17
Apprentissage du soudage......................................29
Accessoires..............................................................46
Entretien...................................................................49
Dépannage ..............................................................54
Schéma de câblage.................................................56
Pièces ......................................................................57
Date of Purchase:
Serial Number:
Code Number:
Model:
Where Purchased:
Copyright © 2001 Lincoln Global Inc.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Lincoln Electric MIG-PAK 10 and is the answer not in the manual?

Lincoln Electric MIG-PAK 10 Specifications

General IconGeneral
TypeMIG Welder
Input Power20A
Rated Output90A @ 20% Duty Cycle
Input Current @ Rated Output20A
Duty Cycle20% @ 90A
Output Current Range30-90A
Wire Feed Speed50-500 IPM
Wire Feed Speed Range50-500 IPM
Dimensions (H x W x D)14 in
Dimensions14 in
Wire Size Range0.023-0.035 inch

Related product manuals