Why won't my Logik L614WD13 start?
If your Logik Washer/Dryer won't start, make sure the door is closed tightly, the power plug is correctly inserted, the water supply tap is open, the Power button is pressed, and the Start/Pause button is also pressed.
What to do if my Logik L614WD13 is not draining properly?
If your Logik Washer/Dryer isn't draining, rinse the filter of the draining pump and check the drainpipe for blockages.
What to do if my Logik L614WD13 Washer/Dryer is leaking water?
If your Logik Washer/Dryer is leaking, check and tighten the water hose connections if they are loose. If the drain pipe is blocked, clean it. If the leakage is due to too much foam, use a reduced foam detergent.
What to do if my Logik L614WD13 has water overflowing from the bottom?
If water is overflowing from the bottom of your Logik Washer/Dryer, fix the inlet hose if it is not connected firmly or replace the drain hose if it has a water leakage.
What to do if the Logik L614WD13 Washer/Dryer door is not locking?
If the locking door function on your Logik Washer/Dryer is malfunctioning, try reclosing the door.
Why are the washing results not good with my Logik L614WD13?
If your Logik Washer/Dryer isn't cleaning clothes well enough, select a more appropriate wash programme if the clothes are very dirty. Also, ensure you are using enough detergent as per the instructions on the detergent packaging.
How to fix unbalanced load protection on Logik L614WD13 Washer/Dryer?
To address the unbalanced load protection function on your Logik Washer/Dryer: * For single items like carpets, bed sheets, or table sheets, ensure they are symmetrically placed inside the drum. * Reduce the wet weight of laundry by manually wringing out excess water and repositioning items symmetrically in the drum. * Take out and reposition the laundry for more balanced distribution on the inner drum wall. * Add one or two more laundry items to balance the load. * Restart the spin cycle using the Spin program.
Why is the indicator light not working on my Logik Washer/Dryer?
If the indicator or display on your Logik Washer/Dryer isn't lighting up, check that the power is on and the power plug is correctly connected. Also, check the mains plug and fuse, and ensure that the washing machine is turned on.
What to do if my Logik L614WD13 has water intake malfunction?
If your Logik Washer/Dryer has a water intake malfunction, check if the water pressure is too low or if the water supply is cut off.
Explains how to use each button and function for operating the washing machine.
Outlines critical safety precautions to be observed before and during maintenance.
Identifies common issues that do not necessarily indicate a fault and require no service intervention.
Troubleshooting steps for error codes Err1 (door issue) and Err2 (drainage issue).
Troubleshooting steps for error codes Err3 (temperature sensor) and Err4 (heater).
Troubleshooting steps for error code Err5 (water level not reached).
Troubleshooting steps for error code Err7 (motor speed abnormal).
Diagnostic steps for when the washing machine display shows no output.
Troubleshooting guide for issues related to the washing machine not filling with water.
Diagnostic steps for resolving problems where the washing machine does not drain.
Troubleshooting for abnormal noise, vibration, and water leaking issues.
General| Load Capacity (Washing) | 6 kg |
|---|---|
| Spin Speed | 1400 rpm |
| Number of Programs | 15 |
| Colour | White |
| Energy efficiency class | B |
| Washing performance class | A |
| Spinning performance class | B |
| Quick wash time | 15 minutes |
| Dimensions (H x W x D) | 850 x 600 x 580 mm |
To Next Page
