LUMENIS PULSE 120H - User Manual

Questions and Answers

T
Travis NicholsAug 17, 2025
What to do if a notification appears on the Lumenis Medical Equipment control screen?
- A
  Adam RodriguezAug 17, 2025
  If a notification appears on the control screen of your Lumenis Medical Equipment, first, clear the message by pressing the Acknowledge button and follow the suggested steps intended to clear the fault. If the same notification appears again, turn off the laser system for one minute and restart it to resume normal operation. If the notification continues to appear, record the error number and contact your local Lumenis service representative.
E
Elizabeth WattsAug 20, 2025
What to do if I get a Cooling System Notification on my Lumenis Medical Equipment?
- L
  lwatkinsAug 20, 2025
  If you receive a cooling system notification on your Lumenis Medical Equipment, first press the Show Notifications icon to see the nature of the notification. Then, clear the message by pressing the Acknowledge button and pause operation for one minute to allow the system to cool. Resume normal operation; if the same notification appears again, turn off the laser system for five minutes and restart it. If the notification persists, record the error number and contact your local Lumenis service representative.
T
thomas13Aug 22, 2025
Why does my LUMENIS PULSE 120H system not turn on?
- J
  Jennifer RojasAug 22, 2025
  If your Lumenis Medical Equipment system does not turn on, check the following: 1. Ensure the laser is plugged in. 2. Set the laser's main circuit breaker to the On (up) position. 3. Turn on the main electrical service power. 4. Try another outlet, or have the outlet professionally tested and repaired if necessary.
D
Dana LongAug 26, 2025
How to fix an Initialization Problem Screen on LUMENIS PULSE 120H?
- A
  adam31Aug 26, 2025
  If your Lumenis Medical Equipment displays an Initialization Problem screen, start by writing down the error number. Then, press the Shutdown button. If the problem re-occurs, contact Lumenis service. Turn on the system with the keyswitch in the Off position. Export logs and send them to Lumenis service.
T
tina86Aug 28, 2025
What to do if the Fiber Expired on LUMENIS PULSE 120H?
- C
  chapmanlisaAug 28, 2025
  If the Lumenis Medical Equipment fiber has expired, replace it with a new one and resume normal operation. If the problem persists, contact Lumenis Service.
N
nicholas49Aug 30, 2025
What to do if my Lumenis Medical Equipment shows 'Unrecognized Fiber'?
- J
  Julian JonesAug 30, 2025
  If your Lumenis Medical Equipment shows 'Unrecognized Fiber', replace the fiber with a Lumenis compatible one and resume normal operation. If the problem persists, contact Lumenis Service.
B
Brianna RobertsonSep 1, 2025
What happens if the Fiber Exceeded Recommend # of Uses on my Lumenis Medical Equipment?
- A
  Alexandra DanielSep 1, 2025
  If the Lumenis Medical Equipment fiber has exceeded the recommended number of uses, be aware of this and replace the optical fiber with a new one.
C
Chad BarnettSep 4, 2025
How to fix Fiber Burn Back on Lumenis Medical Equipment?
- R
  Robin MartinSep 4, 2025
  If you experience fiber burn back with your Lumenis Medical Equipment, which may occur during prolonged procedures, especially when using higher power, renew the fiber tip by stripping and cleaving the fiber.
R
Rachel BlackSep 6, 2025
What to do if I hear 'Popping' or 'Tapping' sound from the Fiber Port of my Lumenis Medical Equipment?
- T
  Terry NguyenSep 7, 2025
  If you are experiencing a 'Popping' or 'Tapping' sound coming from the fiber port of your Lumenis Medical Equipment, this is probably due to a malfunction of the fiber connector. Replace both the fiber and the debris shield.
T
Teresa NguyenSep 9, 2025
Why is there Inadequate or No Aiming Beam on my LUMENIS PULSE 120H Medical Equipment?
- P
  pattonteresaSep 9, 2025
  If you observe inadequate or no aiming beam on your Lumenis Medical Equipment, adjust the aiming beam intensity. Also, replace the delivery system. Lower the intensity of the endoscopic camera light. Inspect and, if necessary, replace the debris shield. If the issue persists, contact your local Lumenis service representative.