Special Safety Rules For
Bandsaws
Always stop the bandsaw before removing scrap pieces from the table.
Always keep hands and fi ngers away from the blade.
Never attempt to saw stock that does not have a fl at surface, unless a
suitable support is used. Always hold material fi rmly and feed it into the
blade at a moderate speed. Always turn off the machine if the material is
to be backed out of an uncompleted cut. Adjust the upper guide about 1/8”
above the material being cut. Check for proper blade size and type for the
thickness and type of material being cut. Make sure that the blade tension
and blade tracking are properly adjusted. Make “relief” cuts before cutting
long curves. Release blade tension when the saw will not be used for a long
period of time.
User Responsibility / Warranty
This machine will perform in conformity with the description contained
in the instructions provided. This machine must be checked periodically.
Defective equipment (including power cable) should not be used. Parts that
are broken, missing, obviously worn, distorted or contaminated, should be
replaced immediately. Should such repair or replacement become necessary,
it is recommended that only genuine replacement parts are used and that
such repairs are carried out by qualifi ed persons. This machine or any of
its parts should not be altered or changed from standard specifi cations. The
user of this machine shall have the sole responsibility for any malfunction
that results from improper use or unauthorized modifi cation from standard
specifi cations, faulty maintenance, damage or improper repair by anyone
other than a qualifi ed person.
This machine is covered by warranty providing the nature of the claim is
the result of faulty workmanship or from a breakdown in basic materials
and is not caused either directly or indirectly through mis-use or abuse and
providing that such a claim is first reported to the selling agent from whom
the machine was originally purchased. Any faulty parts or equipment may
require return to the selling agent suitably packed and freight pre-paid.
The warranty is valid for a period of twelve months starting from the pur-
chase date and consists of the replacement of faulty parts (labour and freight
not included) which are found to be defective. The warranty will be void if
any unauthorised persons tamper with the machine or equipment.
Contents
1.0 Getting to know your bandsaw
35
2.0 Specification 35
3.0 Assembly 35
4.0 Adjustment 36
5.0 Operation 38
6.0 Maintenance 38
7.0 Wiring diagram 38
8.0 Troubleshooting 39
Exploded view 92
EC Declaration of conformity 95
ENGLISH
1.0 Getting to know your
bandsaw
A. Lifting Ring
B. Tension Indicator Window
C. Blade Tension Wheel
D. Switch Unit
E. Rip Fence Assembly
F. Belt Tension & Speed Change
Handwheel
G. Blade Guide
H. Rise & Fall Handwheel
J. Balde Tension Cam Handle
K. Rise & Fall Lock Knob
L. 100mm Dust Extraction Port
M. Motor
N. Table Tilting Knob
O. Blade Tracking Knob
2.0 Specification
Art.
Nr 20005-0102
Luna BBS 500
Max. Depth of Cut: 285mm
Throat Width: 465mm
Sawblade Length: 3607mm
Sawblade Width: 6~25mm
Sawblade Tilt:
Sawtable Size: 630x480mm
Sawblade
Motor: 2.0HP (Output)
3.0 Assembly
The machine is supplied partly assembled. Prior to use, the following items
have to be assembled; working table, rip fence and crank handle.
W
ARNING! Use a 2000kg wrecker hang to lift up this bandsaw with Ring
(Fig.1) to suitable place. To ensure suffi cient upright stability of
this bandsaw and safety, you need to bolt this bandsaw to fl oor on M10
screw.
Fig.1
35
0°~45°
Orig
inal instructions
P. Emergency stop switch
820m/min
380
or
Speed:
To Next Page
Loading...
