Home
MacDon
Farm Equipment
A30-S
MacDon A30-S Unloading And Assembly Instructions
56 pages
Manual
Specs
Ask a question
To Next Page
To Next Page
Loading...
169001
Revision E
A30-S and A30-D
Pull-Type Mower Conditioner
Unloading and Assembly Instructions
Published: August, 2012
2
Table of Contents
Introduction
3
Table of Contents
3
General Safety
5
Recommended Torques
7
General
7
Sae Bolts
7
Metric Bolts
7
Hydraulic Fittings
8
Conversion Table
10
Definitions
10
Step 1. Unload Articulating Power Tongue (Apt)
11
Truck Flatbed
11
Container
11
Step 2. Unload Header
12
Truck Flatbed
12
Container
12
Step 3. Remove Side Deflectors
13
STEP 4. INSTALL GAUGE ROLLERS (Optional)
13
STEP 5. INSTALL ADDITIONAL SKID SHOES (Optional)
13
Step 6. Lower Mower Conditioner
14
Step 7. Install Wheels
15
Step 8. Remove Shipping Channels and Blocking
16
Step 9. Unpack Apt
17
Step 10. Attach Apt
18
Step 11. Connect Hoses
19
Step 12. Attach Mower Conditioner to Tractor
20
Drawbar Type Hitch
20
3-POINT HITCH (Cat. II, III, IIIN)
23
Step 13. Attach Hydraulics and Electrical
25
Step 14. Install Steering Cylinder
27
Step 15. Install Roll Opener Links
29
Step 16. Install Forming Shield Cover
30
Step 17. Install Side Deflectors
30
Step 18. Adjust Center-Link
32
Mechanical Link
32
Hydraulic Link
32
Step 19. Adjust Float Springs
32
Step 20. Reposition Sickle Drive Box Breather
33
Step 21. Adjust Lean Bar
33
Step 22. Adjust Transport Lights
33
Step 23. Install Options
34
Gauge Rollers
34
Skid Shoes
35
Stub Guards
35
Hydraulic Header Angle
36
Tall Crop Divider Kit
36
Step 24. Lubricate Mower Conditioner
37
Header Drive: A30-S
38
Header Drive: A30-S
39
Header Drive: A30-D
40
Header Drive: A30-D
41
Hay Conditioner: A30-S
42
Hay Conditioner: A30-D
43
Carrier
44
Articulating Power Tongue (Apt)
45
Step 25. Perform Pre-Delivery Checks
46
Drive Belts and Chains
46
Auger Stripper Bar Clearance
48
Reel Tine to Header Pan Clearance
48
Header Flotation
48
Conditioner Rolls
49
Skid Shoes/Gauge Rollers
50
Lights
50
Run-Up Mower Conditioner
51
Knife
52
Manuals
52
Other manuals for MacDon A30-S
Operator's Manual
192 pages
Assembly Instructions
56 pages
Need help?
Do you have a question about the MacDon A30-S and is the answer not in the manual?
Ask a question
MacDon A30-S Specifications
General
Knife Drive
Hydraulic
Header Type
Draper
Power Requirements
100 HP
Header Width
30 ft (9.1 m)
Cutting Width
30 ft (9.1 m)
Related product manuals
MacDon A30-D
192 pages
MacDon A40D
270 pages
MacDon M155
510 pages
MacDon 5020
82 pages
MacDon M150
234 pages
MacDon M105
384 pages
MacDon M205
514 pages
MacDon R116
294 pages
MacDon M1170
528 pages
MacDon M155 2022
526 pages
MacDon FlexDraper FD2 Series
2 pages
MacDon FlexDraper FD1 Series
628 pages
Need help?
General
To Next Page
