To Next PageTo Next Page
Need help?Do you have a question about the Mackie PPM1012 and is the answer not in the manual?
General| Type | Analog Mixer |
|---|---|
| Channels | 12 |
| Phantom Power | Yes |
| Tape Input/Output | Yes |
| Inputs - Mic Preamps | 6 XLR |
| Inputs - Line | 8 |
| Outputs - Main | 2 |
| EQ | 3-band |
| Aux Sends | 2 |
| Effects | Yes |
| Headphone Output | 1/4" |
| Power Supply | AC |
| Height | 3.5" |
| Depth | 12.5" |
| Microphone Preamps | 6 x Mic |
| Width | 19 inches |
Connects the mixer to AC power via a 3-prong IEC cord.
Rocker switch to turn the mixer on and off.
Provide power amplifier output to passive speakers.
Allows air flow for cooling internal power amplifiers.
Phantom-powered, balanced inputs for microphones.
1/4" jacks for balanced/unbalanced sources, share circuitry with mic preamps.
Line-level inputs accepting instrument signals with hi-z switch.
Stereo inputs for stereo line-level sources.
Unbalanced 1/4" jacks for connecting serial effects processors.
1/4" TRS connectors for sending monitor line-level output to stage monitors.
1/4" TRS connectors for sending FX line-level outputs to external processors.
1/4" TRS inputs for stereo processed output from external effects.
Stereo RCA inputs for playing tape/CD during breaks.
Stereo RCA outputs for recording main mix.
1/4" TRS jacks for serial effects processors on the main mix.
Balanced 1/4" TRS and XLR outputs for line-level main mix.
1/4" TRS and XLR outputs for main mix summed in mono.
1/4" TRS connector for stereo headphones.
Controls the signal level to stereo headphones.
Connects a footswitch to control internal effects processors.
12V socket for connecting a BNC lamp.
Humorous mention of a control not found on Earth models.
Describes mono channels, compressors, hi-z switches, and 3-band EQ.
Describes stereo channels and 4-band EQ.
Explanation of the "U" symbol indicating unity gain on controls.
Overview of the signal path through the channel strip.
Adjusts input sensitivity for optimal internal operating levels.
High-pass filter cutting bass frequencies below 100 Hz.
In-line compressor with variable threshold for dynamic range control.
Engages guitar direct input for channels 7 or 8 without a DI box.
Details mono and stereo channel EQ bands and usage.
Boosts or cuts high frequencies above 12 kHz.
Adjusts the amount of boost or cut for the mid EQ.
Sets the center frequency for the mid EQ level control.
Adjusts high-mid frequencies on stereo channels.
Adjusts low-mid frequencies on stereo channels.
Boosts or cuts low frequencies below 80 Hz.
Controls for setting up independent stage monitor mixes.
Controls for setting up independent internal effects processor mixes.
Adjusts signal balance between left and right main mix for mono/stereo channels.
Mutes channel signal from reaching main mix and aux busses.
Indicates channel signal strength and overload.
Adjusts the level of each channel onto the main mix.
Allows auditioning of soloed channels in headphones.
Indicates when the mixer is connected to live AC mains and powered on.
Supplies +48V phantom power to XLR microphone inputs.
9-band graphic EQ for tailoring the main mix sound.
9-band graphic EQ for adjusting the monitor 1 mix.
Switch to assign main EQ to main mix or monitor 2.
Indicate when power amplifier channels are overloaded internally.
Stereo meters showing left/right main mix levels.
LED indicating when one or more channels are soloed.
Switch for enhanced clarity with Mackie passive speakers.
Disconects main mix for tape input playback.
Knob to control level of tape input during breaks.
Selects signal paths for internal power amplifiers (Stereo, Mono/Mon1, Mon1/Mon2).
Adds a low-pass filter to mono outputs for subwoofer use.
Adjusts the level of the mono line-level outputs.
Adjusts level of internal FX1 output added to monitor mixes.
Adjusts stereo effects return levels added to the main mix.
Controls monitor mix levels sent to line/speaker outputs.
Adjusts levels of main mix signals to line/speaker outputs.
Controls signal levels going into internal effects processors.
Dual-LEDs indicating signal presence or overload for effects processors.
Shows the number of the currently selected effects preset.
Selects presets and offers tap delay function.
Mutes the internal effects processor output.
Describes 3-pin female XLR connectors for microphone inputs.
Explains mono 1/4" TS plugs/jacks for unbalanced connections.
Explains stereo/balanced 1/4" TRS plugs/jacks.
Describes RCA plugs/jacks for home stereo and video equipment.
Details wiring Speakon connectors for connecting loudspeakers.
Explains Mackie's 1/4" phone inserts for send/receive signals.
Recommends conductor sizes for loudspeaker cable lengths.
