Need help?Do you have a question about the Macurco CM-6 and is the answer not in the manual?
General| Brand | Macurco |
|---|---|
| Model | CM-6 |
| Category | Carbon Monoxide Alarm |
| Language | English |
Provides a high-level overview of the CM-xx device and its capabilities.
Lists critical safety warnings and precautions for device usage to prevent injury or death.
Describes the intended applications and compliance standards for the CM-xx detectors.
Specifies environments and conditions where the CM-xx should not be used to ensure proper function.
Lists the key features and capabilities of the CM-xx device, such as relay activation and current loop.
Details power, current, size, and environmental specifications for CM-6 and CM-12 models.
Provides guidance on optimal mounting locations for the CM-xx detector for effective air monitoring.
Details the installation process for the CM-6 low voltage model, including wiring and connections.
Details the installation process for the CM-12 line voltage model, including wiring and connections.
Describes wiring for power, fan relay, alarm relay, and 4-20mA signals for the CM-6 model.
Describes wiring for power, fan relay, alarm relay, and 4-20mA signals for the CM-12 model.
Describes the device's self-test cycle upon power application and normal operation start.
Explains what the display shows in different states (clean air, fan, alarm) when 'On'.
Explains display behavior and indicators when the display function is turned 'Off'.
Details the behavior of the 4-20mA loop in clean air, gas read, and trouble conditions.
Lists the default pre-programmed settings for Power Up Test, Display, Buzzer, and Relays.
Describes the procedure to reset the device to its original factory default settings.
Explains how to enable or disable the power-up test feature.
Explains how to configure the display to be 'On' or 'Off'.
Explains how to enable or disable the device's buzzer.
Details how to set the CO concentration threshold for the alarm relay.
Explains how to configure the alarm relay for Normally Open (N.O.) or Normally Closed (N.C.).
Details how to set the CO concentration threshold for the fan relay activation.
Explains how to configure the delay time before the fan relay activates.
Details how to set the minimum runtime duration for the fan relay.
Explains how to configure the fan relay to latch or not latch.
Explains how to enable the fan relay to activate during trouble conditions.
Explains how to configure the 4-20mA output setting to basic, enhanced, or off.
Details how to set calibration reminders in months.
Describes the unit's self-monitoring capabilities and how it reports errors.
Lists common issues and interpretations of the 4-20mA loop output.
Lists and explains various error codes displayed by the unit for diagnostics.
Explains factors that can deteriorate sensor performance due to environmental contaminants.
Describes the end-of-life indicator and its management, including silencing and reset.
Details the procedure to reset the sensor life indicator after replacement or maintenance.
Provides instructions for cleaning the device exterior using appropriate materials.
Describes the automatic self-test sequence of the CM-6 unit.
Explains how to perform individual tests on relays, analog output, and sensor response.
Details required kits and essential steps for performing calibration and bump tests.
Describes the procedure to test the fan relay functionality using calibration gas.
Describes the procedure to test the alarm relay functionality using calibration gas.
Details testing the 4-20mA output functionality with calibration gas.
Describes a quick functionality test using aerosol Carbon Monoxide gas.
Outlines the step-by-step process for performing field calibration of the CM-xx unit.
Shows the primary navigation paths within the device's menu system.
Details the flow for accessing and executing tests within the auto-test menu.
Illustrates the menu flow for setting default values and configurations.
Illustrates the menu flow for configuring the power-up test setting.
Illustrates the menu flow for configuring the display mode.
Illustrates the menu flow for configuring the buzzer mode.
Illustrates the menu flow for setting alarm relay thresholds.
Illustrates the menu flow for configuring alarm relay (N.O./N.C.).
Illustrates the menu flow for setting fan relay activation thresholds.
Illustrates the menu flow for configuring fan relay delay.
Illustrates the menu flow for setting fan relay minimum runtime.
Illustrates the menu flow for configuring fan relay latching.
Illustrates the menu flow for enabling trouble fan setting.
Illustrates the menu flow for configuring the 4-20mA output.
Illustrates the menu flow for setting calibration reminders.
Details the menu flow for performing buzzer tests.
Details the menu flow for performing alarm relay tests.
Details the menu flow for performing fan relay tests.
Details the menu flow for performing current loop tests.
Details the menu flow for performing gas tests.
Shows the time elapsed since the last calibration.
Details the menu flow for performing the Span CO calibration.
Details the menu flow for resetting the CO sensor expiry status.
To Next Page