To Next PageTo Next PageWhy do fumes enter the room when my Magiglo Indoor Fireplace is on?
If fumes enter the room when your Magiglo Indoor Fireplace is in operation, it could be due to a blocked flue. Remove the blockage in the flue to resolve this issue. Alternatively, there might be insufficient replacement air. Ensure that air vents are free of obstructions.
What to do if the pilot light goes out when I release the control on my Magiglo Indoor Fireplace?
If the pilot light on your Magiglo Indoor Fireplace lights but goes out when the control is released, there are a couple of potential causes. First, check for a loose thermocouple connection at the control valve end. Remake the thermocouple, ensuring the connection is firm. If the problem persists, the thermocouple itself may be faulty, and you should replace the complete pilot assembly.
How to fix no spark at the electrode in my Magiglo Elite ME16T?
If no spark appears at the electrode of your Magiglo Indoor Fireplace, it could be due to several reasons. The electrode might be cracked or broken, in which case you should replace the pilot assembly. Another possibility is that the HT lead is shorting out on the burner body. Establish where the spark is occurring and insulate or re-route the lead accordingly. Lastly, the spark generator might be faulty, requiring you to replace the valve.
Why do the pilot and main burner go out when I set my Magiglo Elite ME16T Indoor Fireplace to high?
If the pilot and main burner of your Magiglo Indoor Fireplace go out when the control is set to the high position, here's what might be happening: * The gas supply could be partially blocked. Locate the restriction and remove the faulty section. * There might be too many bends on the gas inlet pipe. Increase the diameter and/or reduce the number of bends. * The pilot jet could be partially blocked. Replace the complete pilot assembly. * There may be a restriction at the isolation valve. Ensure the valve is fully open and that the internal diameter is sufficient and free from grease.
What to do if the piezo works, but the pilot light won't light on my Magiglo Elite ME16T Indoor Fireplace?
If the piezo operates normally but the pilot light won't ignite on your Magiglo Indoor Fireplace, it could be due to a couple of reasons. First, check that there is a gas supply by checking the isolation valve/supply. If gas supply isn't the issue, the pilot jet may be blocked, in which case you should replace the pilot assembly.
Why does my Magiglo Elite ME16T only burn on one side?
If your Magiglo Indoor Fireplace burns with flames only on one side, it could be due to the imitation fuel layout being incorrect. Re-lay the imitation fuel in accordance with the instructions. Alternatively, there might be excessive draught. Establish the cause and rectify it.
General| Brand | Magiglo |
|---|---|
| Model | Elite ME16T |
| Category | Indoor Fireplace |
| Language | English |
Safety warning about the oxygen depletion sensor.
Specifications for fire fret dimensions and compatibility.
Step-by-step guide for lighting the gas fire.
Instructions for replacing batteries in the remote control handset and receiver.
Steps to replace batteries in the optimum control wall box.
Procedure for changing batteries in the trim switch control.
Guidance on arranging imitation coals or pebbles for the desired flame effect.
Instructions for fitting the decorative trim to the thermobox.
Advice on home improvements and their impact on fire safety.
Guidelines for cleaning and maintaining the gas fire.
Essential safety precautions before starting installation.
Specifications and guidelines for flue installation.
Key technical specifications for all models.
Diagrams showing burner tray configurations for different models.
Guidelines for positioning the appliance safely.
Requirements for room ventilation based on heat output.
List of items included in the fire package.
Steps for installing the fire with a Magiglo Thermobox.
Steps for installing the fire itself into the fireplace.
General rules for carrying out servicing.
Specific steps and checks for servicing the appliance.
Procedure for replacing the pilot assembly.
Procedure for replacing the gas injector.
Procedure for replacing the control valve.
Procedure for replacing the gas rate adjusting motor.
