How to set the time and date automatically on my MAJORITY Radio?
To set the time and date automatically on your MAJORITY Radio, turn on the system and switch to DAB radio and let it scan. Then, press the ‘Power Mode’ button, and the system will go into standby. The date and clock will then update automatically.
What to do if my MAJORITY CB24-DAB-BLK buttons are not working?
If the buttons on your MAJORITY Radio are not working, turn off the unit and then turn it back on after a few seconds. This might reset the system and restore button functionality.
What to do if my MAJORITY CB24-DAB-BLK Radio has no sound?
If your MAJORITY Radio has no sound, there might be a few reasons: * The station might not be properly tuned. Try fine-tuning the station. * The volume could be set too low. Increase the volume. * Headphones might be connected. Disconnect them to play sound through the speakers.
Why is my MAJORITY Radio sound distorted?
If the sound from your MAJORITY Radio is distorted, the volume may be too high. Try adjusting the volume control to a lower level.
What to do if my MAJORITY CB24-DAB-BLK Radio display shows “No Service”?
If your MAJORITY Radio displays “No Service”, it indicates that there is no DAB coverage in your area or the reception is poor. Try adjusting the position of the aerial or moving the unit to a location with a stronger signal.
Why is the FM on my MAJORITY CB24-DAB-BLK Radio static or the DAB burbling?
If you are experiencing static sound on FM or burbling/intermittent cut-out on DAB with your MAJORITY Radio, the signal reception is likely low. To resolve this, adjust the aerial or move the unit to a location with a stronger signal. You may also need to re-scan for stations.
What to do if I can't find the desired station on my MAJORITY CB24-DAB-BLK Radio?
If you cannot find the desired station on your MAJORITY Radio, it may be due to a weak signal. Try using the manual tune function to find the station.
What to do if my MAJORITY Portable Radio has static or burbling sound?
If you are experiencing static on FM or burbling/intermittent cut-out on DAB, it is likely due to a low signal. Try adjusting the aerial, or move the unit to a location with a stronger signal. You may also need to rescan for stations or perform a factory reset.
Why is there no sound coming from my MAJORITY Portable Radio?
If there is no sound, the station may not be tuned in properly. Please perform a rescan for available stations or manually scroll through available stations.
What to do if I can't find a station on my MAJORITY Portable Radio?
If you cannot find a desired station, it may be due to a weak signal. Use the manual tune function and try rescanning in a different area.
Details about ports and connectors on the side of the device.
Identifies the buttons located on the top panel of the device.
Identifies the antenna and battery compartment on the back.
Initial steps for turning on the unit and basic radio use.
Instructions for scanning and tuning DAB stations.
How to save and recall favorite DAB radio stations.
Instructions for scanning and tuning FM radio stations.
How to save and recall favorite FM radio stations.
Details on information displayed for DAB and FM radio.
Manual setup procedures for the time and date.
Configuration steps for setting up the dual alarm.
Managing alarm sounds and the snooze function.
Procedure for performing a factory system reset.
How to view the current software version.
How to program the automatic power-off sleep timer.
Details about ports and connectors on the side of the device.
Identifies the buttons located on the top panel of the device.
Identifies the antenna and battery compartment on the back.
Initial steps for turning on the unit and basic radio use.
Instructions for scanning and tuning DAB stations.
How to save and recall favorite DAB radio stations.
Instructions for scanning and tuning FM radio stations.
How to save and recall favorite FM radio stations.
Details on information displayed for DAB and FM radio.
Manual setup procedures for the time and date.
Configuration steps for setting up the dual alarm.
Managing alarm sounds and the snooze function.
Procedure for performing a factory system reset.
How to view the current software version.
How to program the automatic power-off sleep timer.
To Next Page
General