EasyManuals Logo

Manitou MLA 628 -120 LSU 3-E2 Series User Manual

Manitou MLA 628 -120 LSU 3-E2 Series
130 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #116 background imageLoading...
Page #116 background image
3 - 363 - 36
- Loosen high pressure connectors 3 (fig. G1/3) of all the injectors.- Loosen high pressure connectors 3 (fig. G1/3) of all the injectors.
- Activate the starter until the diesel fuel flows out free of air at high pressure connectors- Activate the starter until the diesel fuel flows out free of air at high pressure connectors
3 (fig. G1/3).3 (fig. G1/3).
Do not engage the starter motor on a continual basis for more than 30 seconds and let it cool
Do not engage the starter motor on a continual basis for more than 30 seconds and let it cool
between unsuccessful attempts.between unsuccessful attempts.
- Tighten the connection while the diesel fuel is flowing out (tightening torque 22 ft/lb).- Tighten the connection while the diesel fuel is flowing out (tightening torque 22 ft/lb).
- Install the muffler 1 (fig. G1/1).- Install the muffler 1 (fig. G1/1).
- The I.C. engine is then ready to be started up.- The I.C. engine is then ready to be started up.
- Turn the I.C. engine over slowly for 5 - Turn the I.C. engine over slowly for 5 minutes immediately after bleeding the minutes immediately after bleeding the fuel feed cir-fuel feed cir-
cuit,cuit, in order to ensure that the injection pump has been bled thoroughlyin order to ensure that the injection pump has been bled thoroughly..
NOTENOTE : If the I.C. en: If the I.C. engine functions correctly for a short time then stops or functions gine functions correctly for a short time then stops or functions irreg-irreg-
ularly,ularly, check for poscheck for possible leaks in thsible leaks in the low pressure e low pressure circuit. If in circuit. If in doubt,doubt, contact yourcontact your
dealer.dealer.
G1/3G1/3
33
33
33
33
22
Do not engage the starter motor on a continual basis for more than 30 sec-Do not engage the starter motor on a continual basis for more than 30 sec-
onds and let it cool between unsuccessful attempts.onds and let it cool between unsuccessful attempts.
IMPORTANTIMPORTANT
G2 - WG2 - WHEELHEEL
CHANGECHANGE
In the event of a
In the event of a wheel being changed on the public highway, make sure of wheel being changed on the public highway, make sure of the following pointsthe following points ::
For this operation we advise you to use an approved hydraulic jack and safety support (con-For this operation we advise you to use an approved hydraulic jack and safety support (con-
tact your dealer).tact your dealer).
- Park the lift truck,- Park the lift truck, if possible on even and hif possible on even and hard ground.ard ground.
- Put the warning lights on.- Put the warning lights on.
- Immobilize the lift truck in both directions on the axle opposite to the wheel to be- Immobilize the lift truck in both directions on the axle opposite to the wheel to be
changed.changed.
- Unlock the nuts of the wheel to be changed.- Unlock the nuts of the wheel to be changed.
- Place the jack under the flared axle tube,- Place the jack under the flared axle tube, as near as possible to the wheel and adjust theas near as possible to the wheel and adjust the
jack (fig. G2/1).jack (fig. G2/1).
- Lift the wheel until - Lift the wheel until it comes off the ground and put in place the it comes off the ground and put in place the safety support under thesafety support under the
axle (fig. G2/2).axle (fig. G2/2).
- Completely unscrew the wheel nuts and remove them.- Completely unscrew the wheel nuts and remove them.
- Free the wheel by reciprocating movements and roll it to the side.- Free the wheel by reciprocating movements and roll it to the side.
- Slip the new wheel on the wheel hub.- Slip the new wheel on the wheel hub.
- Install the - Install the nuts by nuts by hand,hand, if necessary grease theif necessary grease them.m.
R th f t t d l th lift t k ith th j kR th f t t d l th lift t k ith th j k
G2/1G2/1
G2/2G2/2
In the event of a wheel In the event of a wheel being changed on the public highway, make sure obeing changed on the public highway, make sure off
the following pointsthe following points
WARNINGWARNING
CONTENTSCONTENTS
https://www.forkliftpdfmanuals.com/

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Manitou MLA 628 -120 LSU 3-E2 Series and is the answer not in the manual?

Manitou MLA 628 -120 LSU 3-E2 Series Specifications

General IconGeneral
BrandManitou
ModelMLA 628 -120 LSU 3-E2 Series
CategoryForklifts
LanguageEnglish

Related product manuals