4 - 84 - 8
Make sure that the rapid connectors are clean and protect the holes which are not used, with
Make sure that the rapid connectors are clean and protect the holes which are not used, with
the caps provided.the caps provided.
HAND RELEASING AND HAND RELEASING AND DISCONNECTING THE ATTADISCONNECTING THE ATTACHMENTCHMENT
- - Proceed in the Proceed in the reverse order of reverse order of paragraph HAND LOCKING paragraph HAND LOCKING AND CONNECTING THEAND CONNECTING THE
ATTATTACHMENT while making sure you iACHMENT while making sure you install the locking pin and nstall the locking pin and the clip in the the clip in the bracket (fig.bracket (fig.
A).A).
LAYING AN ATTACHMENTLAYING AN ATTACHMENT
- Proceed in - Proceed in the reverse order of paragraph TAKING UP AN ATTAthe reverse order of paragraph TAKING UP AN ATTACHMENT while making sureCHMENT while making sure
you place the attachment flat on the ground and in closed position.you place the attachment flat on the ground and in closed position.
CC
DD
EE
11
Make sure that the rapid (quick-release) connectors are clean and protec-Make sure that the rapid (quick-release) connectors are clean and protec-
ted with the caps provided when not in use.ted with the caps provided when not in use.
IMPORTANTIMPORTANT
D - HD - HYDYDRARAULULICIC ATATTATACHCHMEMENTNT ANANDD HYHYDRDRAUAULILICC LOCLOCKINKINGG DEDEVIVICECE((OPTIONOPTION))
MLA 628 -120 LSU POWERSHIFT Series 3-E2MLA 628 -120 LSU POWERSHIFT Series 3-E2
TAKING UP AN ATTACHMENTTAKING UP AN ATTACHMENT
- Ensure that the attachment is oriented for locking to the carriage. If it is not correctly- Ensure that the attachment is oriented for locking to the carriage. If it is not correctly
oriented,oriented, take the necessary precautions in ortake the necessary precautions in order to move it safelyder to move it safely..
- Check that the rods on the locking cylinder are retracted (fig. A).- Check that the rods on the locking cylinder are retracted (fig. A).
- Park the lift truck with the boom lowere- Park the lift truck with the boom lowered in front of and pard in front of and parallel to the attachment,allel to the attachment, tilt thetilt the
carriage forwards (fig. B).carriage forwards (fig. B).
- Bring the - Bring the carriage under the carriage under the locking tube of locking tube of the attachment,the attachment, slightly lift the slightly lift the boom,boom, inclineincline
the carriage backwards in order to position the attachment (fig. C).the carriage backwards in order to position the attachment (fig. C).
- Lift the attachment off the ground to facilitate locking.- Lift the attachment off the ground to facilitate locking.
HYDRAULIC LOCKING AND HYDRAULIC LOCKING AND CONNECTING THE ATTACONNECTING THE ATTACHMENTCHMENT
- Put the valve in position A (- Put the valve in position A (fig. D),fig. D), the hydraulic circuit of the hydraulic circuit of the attachment locking open.the attachment locking open.
- Switch button 1 (fig. E) of the distributor lever up to completely lock the attachment on- Switch button 1 (fig. E) of the distributor lever up to completely lock the attachment on
the carriage.the carriage.
- Stop the I.C. engine and keep the ignition on the lift truck.- Stop the I.C. engine and keep the ignition on the lift truck.
- Release the pressure from the attachment hydraulic circuit by pressing button 1 (fig. E)- Release the pressure from the attachment hydraulic circuit by pressing button 1 (fig. E)
on the distributor lever up and down 4 or 5 times.on the distributor lever up and down 4 or 5 times.
- Connect the rapid connectors according to the logic of the attachment’s hydraulic move-- Connect the rapid connectors according to the logic of the attachment’s hydraulic move-
mentsments
AA
BB
CONTENTSCONTENTS
To Next Page
Loading...
