Marantz CD-63 SE - Remote Control Unit Operation; Button Functions

REMOTE CONTROL UNIT RC-63CD
When the power to the CD player is ON and a disc is loaded on the disc
tray, the remote control unit (RC-63CD) can be used to operate the player's
various functions. However, the power to the CD player must be switched
ON/OFF using the POWER switch on the main unit. The AMS, REPEAT,
A-B REPEAT, RANDOM and VOLUME functions are carried out using the
buttons on the remote control unit (RC-63CD).
—-| fos] foe RO} j=} [oO
| [ol] [a
I~]
—_| jf =
ss] io >
REMOTE CONTROL UNIT
—_ co
OPEN/CLOSE button
Press to open and close the disc tray.
[2] DIMMER button
Press to adjust the display illumination brightness. The illumination at its
he brightest when the power is switched ON. Each time this button is
pressed, the brightness dim until the fourth press, after which the
itumination returns to the original brightness.
[3] Numeric (0 to 9) buttons
When used during playback, these buttons allow you to specify the
number of another track you want to play.
When used during stop mode, these buttons allow you to specify the
number of a track from which to start playback.
These buttons are also used to select tracks for programming.
> (Play) button
Press to start playback.
When pressed during playback, the CD player returns to the beginning of
the current track and plays the track again.
11
[5] Ké<¢, BI (Track Previous/Next) buttons
When
the
ké<
button
is
pressed
during
playback,
play
re-starts
at
the
beginning
of
the
previous
or
a
preceding
track.
When
the
PP!
button
is
pressed,
play
re-starts
at
the
beginning
of
the
next
or
a
subsequent
track.
The
same
number
of
tracks
as
the
number
of
times
the
button
is
pressed
can
be
skipped.
- The selected track number is shown on the display.
These
buttons
can
also
be
used
to
select
a
desired
track
from
which
to
start
playback.
These
buttons
are
also
used
in
program
mode
to
select
tracks
for
programming.
[6] << , >> (Search Reverse/Forward) buttons
“44:
When
pressed
during
playback,
this
button
fast-reverses
the
play
position.
bP
»
When
pressed
during
playback,
this
button
fast-forwards
the
play
position.
II (PAUSE) button
Press
to
interrupt
playback
temporarily.
When
pressed
again,
the
indicator
goes out and playback resumes from same position.
(Stop) button
Press
to
stop
playback.
This
button
is
also
used
for
deleting
a
program.
[9] EDIT button
Press to put the CD player into edit mode.
TIME button
Switches
the
time
shown
on
the
display
to
the
remaining
time
of
the
current
track
(REMAIN)
or
the
remaining
time
of
the
entire
disc
(TOTAL
REMAIN).
[11] REPEAT button
Press
to
select
1-track
repeat,
all-track
repeat
or
program
repeat
playback
mode.
[12] CANCEL button
Used to delete specified track numbers from a program.
Also
used
when
creating
programs
by
deleting
any
tracks
which
you
do
not
want
to listen
to (delete
programming).
[13] RECALL button
Pressing
this
button
displays
the
programmed
track
numbers
and
program
numbers (steps) in Sequence.
PROG button
Press to switch between the play mode and program mode.
[15] RANDOM button
When
this
button
is
pressed,
the
player
enters
random
play
mode
(tracks
on
the
disc
are
selected
and
played
in
a
random
order).
When
pressed
again,
random
play
is
cancelled.
[16] AMS (Automatic Music Scan) button
When
this
button
is
pressed,
the
player
automatically
plays
the
first
part
of
each track on the disc for 10 seconds.
17] A-B button
Used
to
set
the
starting
and
stopping
points
of
a
passage
for
repeated
playback.
18] VOL('¥)/VOL(A) buttons
Press
to
vary
the
ANALOG
OUTPUT
and
headphones
output
volume
between
0
and
-30
dB.
The
level
when
the
power
is
turned
on
is
0
dB
(maximum
volume).
NOTE:
The
remote
control
unit
(RC-63CD)
is
a
supplied
as
an
accessory
of
the
CD-53
and
CD-63.
It
is
not
supplied
with
the
CD-43.
An
optional
remote
control
can
be
purchased
for
the
CD-43
if
required.
Because
the
CD-43
does
not
have
a
infrared
remote
sensor
for
the
remote
control,
it
should
be
connected
through
the
REMOTE
CONTROL
IN/
QUT
jacks
to
another
component
which
is
equipped
with
an
infrared
remote
sensor.
For
the
components
that
can
be
remote-controlled,
please
refer
to
the
instruction
manual
supplied
with
the
optional
remote
control.