To Next PageTo Next PageWhat to do if I hear noise during AM reception on my Marantz Stereo Receiver?
If you're experiencing noise during AM reception with your Marantz Stereo Receiver, the interference might be due to other electrical fields. Try relocating the AM indoor antenna.
What to do if control with the remote control unit fails on Marantz SR7001 Stereo Receiver?
If the remote control isn't working with your Marantz Stereo Receiver, consider the following: 1. Replace all batteries with new ones. 2. Ensure you're selecting the correct function-key setting. 3. Move closer to the receiver. 4. Remove any obstructions between the remote and the receiver.
What to do if a specific channel does not produce output on Marantz SR7001 Stereo Receiver?
If a specific channel isn't producing output on your Marantz Stereo Receiver, check the encoded channel on the source side to ensure there is content recorded there.
Why is there no output to Subwoofer Out on my Marantz SR7001?
If there's no output to the Subwoofer Out on your Marantz Stereo Receiver, check if 'Subwoofer = NONE' has been selected in SETUP mode. If so, select 'Subwoofer = YES'.
Why is there no audio output from the surround back speakers on my Marantz SR7001?
If you're not hearing audio from the surround back speakers on your Marantz Stereo Receiver, consider these points: * Make sure the surround back speaker cables are properly connected. * The surround mode must be set to EX/ES to enable the surround back speakers. * Ensure that 'Surround back = NONE' hasn't been selected in SPEAKERS SIZE SETUP; correct the setting if necessary.
Why is there no audio output from the surround speakers on my Marantz SR7001?
If there's no audio from the surround speakers on your Marantz Stereo Receiver, check the following: * Ensure the surround speaker cables are correctly connected. * If 'STEREO' is selected for Surround mode, no sound will be output from the surround speakers; select a different Surround mode. * Confirm that 'Surround = NONE' hasn't been selected in SETUP mode; adjust the setting as needed.
Why is there no audio output from the center channel speaker on my Marantz SR7001 Stereo Receiver?
If you aren't getting any audio from the center channel speaker on your Marantz Stereo Receiver, check these: * Ensure the center speaker cable is correctly connected. * If 'STEREO' is selected for Surround mode, no sound will come from the center speaker; choose another Surround mode. * Verify that 'Center = NONE' hasn't been selected in SETUP mode; correct the setting if needed.
Why is there no speaker output from my Marantz SR7001?
If you're not getting any sound from your speakers, make sure headphones are not connected to the headphone jack, as this will disable speaker output.
General| Channels | 7.1 |
|---|---|
| HDMI Inputs | 2 |
| HDMI Outputs | 1 |
| Dolby Digital | Yes |
| DTS | Yes |
| Component Video Inputs | 3 |
| Component Video Outputs | 1 |
| Preamp Outputs | 7.1 |
| Zone 2 Audio Output | Yes |
| Frequency Response | 10 Hz - 100 kHz (+1, -3 dB) |
| Total Harmonic Distortion | 0.08% |
| Input Sensitivity | 200 mV |
| Signal-to-Noise Ratio | 105 dB |
| Power Consumption | 650W |
| Digital Audio Inputs | 4 (2 optical, 2 coaxial) |
| Analog Audio Inputs | 7 |
| Surround Sound Formats | Dolby Digital, Dolby Digital EX, DTS |
| Weight | 33 lbs |
| Standby Power Consumption | Less than 1W |
