Marantz SR7010 - Page 98

Sound modes and surround parameters
Sound mode
Surround Parameter
Dialog Level
Adjust
Subwoofer Level
Adjust
Cinema EQ
Loudness
Management
z1
Dynamic
Compression
z2
Dialog Control
z3
L ow Frequency
z4
Speaker Select Center Spread
Direct/Pure Direct (2-channel) z5 Sz6 S S
Direct/Pure Direct (Multi-channel) z5 SSSSS
DSD Direct (2-channel)
Sz6
DSD Direct (Multi-channel) z5 S S S
Stereo
SSS
Multi Ch In
SSSS
Dolby Surround
SSSSSS
DTS Neural:X
SSSS
Audyssey DSX®
SSSSSS
Dolby Digital
SSSSSS
Dolby Digital Plus
SSSSSS
Dolby TrueHD
SSSSSS
Dolby Atmos
SSSSSS
DTS Surround
SSSSS
DTS 96/24
SSSS
DTS-HD
SSSS
DTS Express
SSSS
DTS:X
SSSSS
Multi Ch Stereo
SSSSSS
Virtual
SSSSS
z
1 -
z
6 : “Sound modes and surround parameters”
Sound mode
Surround Parameter
Tone
z7
Audyssey
M-DAX
z10
DTS Neural:X
Auro-Matic 3D
Preset
Auro-Matic 3D
Strength
MultEQ® XT32
z8
Dynamic EQ
z9
Dynamic
Volume
z9
Audyssey
LFC™
z9
Audyssey
DSX®
Direct/Pure Direct (2-channel) z5
Direct/Pure Direct (Multi-channel) z5
DSD Direct (2-channel)
DSD Direct (Multi-channel) z5
Stereo
SSSSSS
Multi Ch In
S S SSSS
Dolby Surround
SSSSSS
DTS Neural:X
SSSSSS
Audyssey DSX®
S S S SSS
Dolby Digital
S SSS S S
Dolby Digital Plus
S SSSSS
Dolby TrueHD
S S SSSS
Dolby Atmos
S S SSS
DTS Surround
S S SSS S
DTS 96/24
S S SSS S
DTS-HD
S S SSSS
DTS Express
S S S SSS
DTS:X
SSSSSS
Multi Ch Stereo
SSSSSS
Virtual
SSSSSS
z
5,
z
7 -
z
10: “Sound modes and surround parameters”
Upgrade (Auro-3D)
Sound mode
Surround Parameter
Dialog Level
Adjust
Subwoofer Level
Adjust
Cinema EQ
Loudness
Management
z1
Dynamic
Compression
z2
Dialog Control
z3
Low Frequency
z4
Speaker Select Center Spread
Auro-3D
SSS
Auro-2D Surround
SSS
Sound mode
Surround Parameter
Tone
z7
Audyssey
M-DAX
z10
DTS Neural:X
Auro-Matic 3D
Preset
Auro-Matic 3D
Strength
MultEQ® XT32
z8
Dynamic EQ
z9
Dynamic
Volume
z9
Audyssey
LFC™
z9
Audyssey DSX®
Auro-3D
Sz11 Sz11 SSSSSS
Auro-2D Surround
SSSSSS
z
1 -
z
4,
z
7 -
z
11 : “Sound modes and surround parameters”
z1
This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played.
z2
This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS:X or DTS signal is played.
z3
This item can be selected when a DTS:X signal that is compatible with the Dialog Control function is input.
z4
This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
z5
During playback in Pure Direct mode, the surround parameters are the same as in Direct mode.
z6 This setting is available when “Subwoofer Mode” in the menu is set to “LFE+Main”.
z7 This item cannot be set when “Dynamic EQ” is set to “On”.
z8
This item cannot be set when Audyssey
®
Setup (Speaker Calibration) has not been performed.
z9
This item cannot be set when “MultEQ
®
XT32” in the menu is set to “Off”.
z10
This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
z11
This can be set if the input signal does not contain an Auro-3D signal or if the input Auro-3D signal does not contain Front Height channels.
98