How to fix 'Error System Type Mismatch on Network' on MARLO Water System?
If the MARLO Water System displays 'Error System Type Mismatch on Network', it means the system type among connected units does not match. To correct this, push the correct system settings in Master Settings.
What does 'Flow Meter Error Continuous Flow Detected' mean on my MARLO NXT2 Water Dispenser?
If your MARLO Water Dispenser shows a 'Flow Meter Error Continuous Flow Detected', it means that the flow has exceeded the specified threshold for a specific duration. To fix this, trigger a manual regeneration.
Why does the drain of my MARLO NXT2 Water Dispenser flow continuously?
If the drain of your MARLO Water Dispenser flows continuously, it could be due to several reasons: the valve is not programming correctly (check timer program and positioning of control, replace power head assembly if not positioning properly), foreign material in the control (remove power head assembly and inspect bore, remove foreign material and check control in various regeneration positions), or an internal control leak (replace seals and piston assembly).
What causes excessive water in the brine tank of my MARLO Water Dispenser?
Excessive water in the brine tank of your MARLO Water Dispenser can be caused by a plugged drain line flow control (clean flow control), a plugged injector system (clean injector and screen), the timer not cycling (replace timer), foreign material in the brine valve (replace brine valve seat and clean valve), or foreign material in the brine line flow control (clean brine line flow control).
Why does my MARLO NXT2 softener fail to regenerate?
If your MARLO Water Dispenser softener fails to regenerate, several issues could be the cause. It could be due to an interruption in electrical service (check the fuse, plug, pull chain, or switch), a defective timer (replace the timer), or a power failure (reset the time of day). Other causes include an open by-pass valve (close it), no salt in the brine tank (add salt and maintain the level above the water level), a plugged injector screen (clean it), or insufficient water flowing into the brine tank (check the brine tank fill time and clean the brine line flow control if plugged). Hardness in the hot water tank may also be the reason (repeated flushings of the hot water tank is required), a leak at the distributor tube (make sure the distributor tube is not cracked and check the O-ring ...
How to fix excessive water in brine tank of MARLO Water System?
If you find excessive water in the brine tank of your MARLO Water System, it's likely due to a plugged drain line flow control. Clean the flow control to resolve this issue.
What to do if my MARLO Water System displays 'Flow Meter Error Continuous Flow Detected'?
If the MARLO Water System displays 'Flow Meter Error Continuous Flow Detected', this indicates that the flow has exceeded the specified threshold for a certain duration. To solve this, trigger a manual regeneration.
Why is the drain flowing continuously in my MARLO Water System?
If your MARLO Water System's drain is flowing continuously, this is due to an internal control leak. You should change the seals, spacers, and piston assembly.
What does 'Error System Type Mismatch on Network' mean on my MARLO Water Dispenser?
If your MARLO Water Dispenser displays 'Error System Type Mismatch on Network', it indicates that the system type among connected units does not match. To resolve this, push the correct system settings in Master Settings.
Why does my MARLO NXT2 control cycle continuously?
If your MARLO Water Dispenser control cycles continuously, it is caused by a misadjusted, broken, or shorted switch. Determine if the switch or timer is faulty and replace it, or replace the complete power head.
Details the warranty coverage for commercial and industrial water treatment products.
Provides physical dimensions for various MGT models, aiding in space planning.
Lists key technical specifications, capacities, and flow rates for different system sizes.
Crucial safety precautions and warnings applicable before, during, and after installation.
Specific checks required for components like distributor piping and laterals before media loading.
General safety advisories regarding product installation and use.
Covers operating pressure, power requirements, and unit design considerations.
Guides on locating, erecting, and preparing softener tanks for media loading.
Instructions for positioning and connecting the brine tank, including tubing and overflow.
Covers mounting water meters and connecting network/communication cables between units.
Details electrical power connection and proper piping installation for system integrity.
Explains the functions of LEDs, display screen, and control buttons on the timer.
Describes system modes, timer functions during normal use, and power failures.
Details manual regeneration, programming lock settings, and settings review.
Covers user mode, batch size calculation, and diagnostic mode flow charts.
Explains master programming and provides diagrams of regeneration flow positions.
Provides the NXT2 wiring diagram for electrical connections and troubleshooting.
Illustrates and lists parts for the 2900 Powerhead Assembly.
Shows the NXT2 Timer Assembly and its components.
Illustrates and lists parts for the 2900 Control Valve Body.
Details components and parts lists for 1600 and 1700 Brine Systems.
Describes various meter types and their parts.
Lists components and part numbers for different brine tank sizes.
Lists available service assemblies, kits, and accessories for the system.
Lists error messages, their causes, and recommended corrections for system issues.
Provides a table of common problems with the 2900 valve, their causes, and solutions.
General| Brand | MARLO |
|---|---|
| Model | NXT2 Series |
| Category | Water Dispenser |
| Language | English |
To Next Page