What does 'Motor Stall No Changes Detected in the Optical Sensor for 6 Seconds' mean on my MARLO MGT 240 Water Dispenser?
If your MARLO Water Dispenser displays 'Motor Stall No Changes Detected in the Optical Sensor for 6 Seconds', it means that the motor is on but no encoder pulses are detected within a given duration while homing. Check the P11 connection and trigger a manual regeneration.
Why does my MARLO MGT 240 Water Dispenser softener fail to regenerate?
If your MARLO Water Dispenser softener fails to regenerate, several issues could be the cause. It could be due to an interruption in electrical service (check the fuse, plug, pull chain, or switch), a defective timer (replace the timer), or a power failure (reset the time of day). Other causes include an open by-pass valve (close it), no salt in the brine tank (add salt and maintain the level above the water level), a plugged injector screen (clean it), or insufficient water flowing into the brine tank (check the brine tank fill time and clean the brine line flow control if plugged). Hardness in the hot water tank may also be the reason (repeated flushings of the hot water tank is required), a leak at the distributor tube (make sure the distributor tube is not cracked and check the O-ring ...
Why does my MARLO Water Dispenser show Error Valve Count Mismatch?
The 'Error Valve Count Mismatch' on your MARLO Water Dispenser means that the number of NXT2 valves detected doesn't match the system type selected in Master Programming. To fix this, push the correct valve settings in Master Settings.
What to do if MARLO Water Dispenser displays Motor Stall No Changes Detected in the Optical Sensor?
If you encounter a 'Motor Stall No Changes Detected in the Optical Sensor' error with your MARLO Water Dispenser, it indicates that the motor is active, but no encoder pulses are being detected during homing. To fix this, check the P11 connection and then initiate a manual regeneration.
What to do if MARLO Water Dispenser shows Motor Run-On No CAM Switch Change Detected?
If your MARLO Water Dispenser displays a 'Motor Run-On No CAM Switch Change Detected' error, it means the motor is running, but no encoder pulses are detected, and the CAM switches aren't changing state within a specific timeframe. To resolve this, verify that the correct valve type is selected. Then, trigger a manual regeneration.
What does 'Error Send/Receive Failure' mean on my MARLO MGT 240?
If your MARLO Water Dispenser displays 'Error Send/Receive Failure', it means that during a setting push, a packet was missing. To fix this, reconnect the communication cables and push the settings in Master Settings.
What does 'Error System Type Mismatch on Network' mean on my MARLO MGT 240?
If your MARLO Water Dispenser displays 'Error System Type Mismatch on Network', it indicates that the system type among connected units does not match. To resolve this, push the correct system settings in Master Settings.
What does 'Error Valve Count Mismatch' mean on my MARLO Water Dispenser?
If your MARLO Water Dispenser displays 'Error Valve Count Mismatch', it means that the number of NXT2 detected does not match the selected system type in Master Programming. Push the correct valve settings in Master Settings to resolve this.
Why does my MARLO Water Dispenser control cycle continuously?
If your MARLO Water Dispenser control cycles continuously, it is caused by a misadjusted, broken, or shorted switch. Determine if the switch or timer is faulty and replace it, or replace the complete power head.
What to do if my MARLO MGT 240 Water Dispenser shows '100 Days Without Regen'?
If your MARLO Water Dispenser displays '100 Days Without Regen', it means that 100 days have passed without a regeneration cycle. To resolve this, trigger a manual regeneration.
General| Brand | MARLO |
|---|---|
| Model | MGT 240 |
| Category | Water Dispenser |
| Language | English |
To Next Page