Marshall Amplification DSL40CR Service Manual

REAR PANEL FUNCTIONS
2827
26
313029 32 33
26. MAINS INPUT
Connects the amplier to the mains
electricity supply.
Note: The mains input socket has an
integrated fuse compartment. Ensure that
the value of a replacement fuse matches
the labelling on the amplier rear panel.
You must switch the amplier o and
disconnect it from the mains electricity
supply before aempng to access the
fuse compartment. If in doubt, contact
your Marshall dealer.
27. MIDI IN
Connect your external MIDI device to the
MIDI IN socket.
Note: The amplier only accepts incoming
data and it is not able to send any MIDI
commands.
You can set the channel, the state of
the loop and master volume via MIDI
messages.
MIDI commands allow the remote control
of some front panel funcons (refer to MIDI
implementaon chart in the user manual).
The MIDI receive channel is factory-set
to channel 1. In order to set a dierent
channel, press and hold the Loop On/O
switch (front panel funcon #23) while
powering up the amplier to acvate
MIDI waing mode. The LED will ash
unl a valid MIDI command is received.
The MIDI receive channel will be set to
the channel of that command.
To select MIDI OMNI receive, put the
amplier into MIDI waing mode and
then press and hold the Master Select
switch (front panel funcon #18) unl its
LED lights up.
Note: When the 2-way footswitch is
connected the amplier will not respond
to any MIDI messages.
28. FX LOOP RETURN
Connect the output of an external FX
pedal or processor.
29. FX LOOP SEND
Connect the input of an external FX pedal
or processor.
30. F/S
Connect the supplied 2-way footswitch
or the oponal 6-way footswitch here.
31. AUDIO IN
Connect an external device here to
pracce with or to jam along to music.
32. EMULATED OUT
Emulated line level output for
headphones or connecon to a mixer.
The DSL is equipped with a high quality
emulated output using Soube-designed
studio cabinet emulaon. This ensures
that your headphone and output signal
from this socket provide the best possible
tone for pracce or recording.
Note: Using the emulated out does not
omit the need for a speaker load to be
connected to the amplier (rear panel
funcon #33).
Note: For silent recording via emulated
out set the output switch to STB (front
panel funcon #24).
33. LOUDSPEAKERS
There are ve speaker outputs available.
They are labelled according to the
intended impedances:
• 1 x 16 Ohm: connect a single 16
Ohm speaker cabinet to this jack.
• 1x 8 Ohm or 2 x 16 Ohm: connect
a single 8 Ohm speaker cabinet or
two 16 Ohm speaker cabinets.
• 1 x 4 Ohm or 2 x 8 Ohm: connect
a single 4 Ohm speaker cabinet or
two 8 Ohm speaker cabinets.
WARNING: Although the amplier has
ve speaker outputs, never aempt to
connect more speaker cabinets than
rated. The safe combinaons are: 1 x 16
Ohm, 1 x 8 Ohm, 2 x 16 Ohm, 1 x 4 Ohm
or 2 x 8 Ohm only. Any other speaker
cabinet conguraon may stress the
power amplier secon and in extreme
cases may lead to valve and/or output
transformer failure. Never use DSL100HR
or DSL40CR without a speaker load.
14DSL40CR service manual
BOOK-80015-01 | M3390.069

Marshall Amplification DSL40CR Specifications

General

Brand	Marshall Amplification
Model	DSL40CR
Category	Amplifier
Language	English