EasyManua.ls Logo

Masterbuilt MWG 600B - User Manual

Masterbuilt MWG 600B
56 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Manual Code: 9826190006 190425-GSB
MWG 600B
PELLET GRILL
GRIL À GRANULES
PARRILLA DE PERLAS DE MADERA
Manual applies to the following model number(s)
Le manuel s’applique aux numéros de modèle suivants
El manual se aplica a los siguientes números de modelo
These numbers are located on the rating label of the grill.
Ces numéros se trouvent sur la plaque signalétique du gril.
Estos números se ubican en la etiqueta posterior de la parrilla.
Mfg. Date - Serial Number | Date de fabrication - Numéro de série |
Fecha Fabricado - Número de serie
Your model number | Votre numéro de modèle | Su número de modelo
MB20261719, MB20261819
Please record this information immediately and keep in a
safe place for future use.
Veuillez noter cette information immédiatement et la con-
server dans un endroit sûr pour une utilisation future.
Por favor, registrar esta información inmediatamente y
guardar en un lugar seguro para su uso futuro.
IMPORTANT | IMPORTANTE
Master it. Masterbuilt.
Master it. Masterbuilt.
Welcome to the family. Let’s get started.
Bienvenue à la famille. Commençons.
Bienvenido a la familia. Empecemos.

Table of Contents

Questions and Answers

  • H
    Heidi FischerAug 5, 2025
    Why doesn’t my Masterbuilt Grill fire on smoke setting?
    • J
      Jonathan NelsonAug 5, 2025
      If your Masterbuilt Grill doesn't fire on the smoke setting, it might be because the “P” setting on the digital controller is set too high; review the Digital Controller Functions in the Operating Instructions section to adjust it. Make sure the power switch is OFF and the power cord is disconnected. Open the lid and remove the cooking grate, grease deflector, and heat diffuser. Remove all unburned pellets and ash from the crucible, using a shop-vac if needed, ensuring the grill is cold to prevent fire hazards. Put the heat diffuser, grease deflector, and cooking grate back in place and follow the INITIAL LIGHTING INSTRUCTIONS.
  • W
    William MorganOct 27, 2025
    How to fix a Masterbuilt MWG 600B that fails to ignite?
    • D
      Dustin ObrienOct 27, 2025
      To address a Masterbuilt Grill that won't ignite, start by turning the power switch to OFF and disconnecting the power cord. Remove any food, cooking grate, grease deflector, and heat diffuser. Clear all unburned pellets and ash from the crucible, ensuring the grill is COLD to prevent fire hazards. Restart the grill to check if the ignition cycle works. Verify power at the outlet and reset the ground fault interrupter if needed. Inspect the power cord fuses by disconnecting the cord, removing the controller, and checking the fuse on the back, replacing it if blown. Finally, verify the element, intake fan, and auger drive are functioning by unplugging the element connector (red/white wires), plugging the power cord into a grounded outlet, and turning the power switch to ON. Check that the i...
  • S
    Sandra SandovalNov 12, 2025
    What to do if no pellets are delivered to the crucible in my Masterbuilt MWG 600B?
    • B
      Brenda RodriguezNov 12, 2025
      If no pellets are being delivered to the crucible of your Masterbuilt Grill, first check that there are pellets in the pellet hopper. Remember that it can take up to seven minutes for pellets to travel from the pellet hopper to the crucible. If the issue persists, ensure the power switch is OFF and the power cord is disconnected. Remove the controller and the pellet hopper to access the auger drive motor and intake fan connections. Unplug the auger drive motor (orange/white wire pair) and the intake fan (purple/white wire pair), then reconnect both. If the auger drive motor is working, the digital controller may need to be replaced. If the auger drive motor is not working, but the intake fan is working, the problem is the auger system which may need to be checked. Locate the small fan blad...
  • L
    lhughesNov 19, 2025
    How to fix a Masterbuilt MWG 600B when foreign objects or wet pellets jam the auger system?
    • T
      tylerandrewsNov 19, 2025
      If foreign objects or wet pellets are jamming the auger system of your Masterbuilt Grill, you need to remove the pellet hopper to access the auger drive motor. Remove the bolt and nut connecting the auger drive motor shaft to the auger shaft and the screw holding the auger retainer to the auger tube. Use a small pipe wrench or locking pliers on the auger shaft to turn the auger counterclockwise until it breaks free. Remove the auger and clean all pellets, ash, or foreign objects from the auger, auger tube, and crucible. Sand the outside surfaces of the auger with medium grit sandpaper and the inside of the auger tube if necessary. Vacuum any sanding grit out of the auger tube and crucible. Reinstall the auger bushing and the auger into the auger tube, ensuring the auger rotates freely. Fin...

Summary

Safety Warnings and Safeguards

Structural Proximity and Safe Usage

Creosote Formation and Removal

Pre-Assembly Instructions

Parts List

Hardware List

Assembly Instructions

Assembly Steps 1-2

Assemble the grill legs and attach the bottom shelf.

Initial Lighting Instructions

Lighting Instructions

Controller Shut Down Cycle

Explains the automatic shutdown cycle of the grill controller after cooking.

Operating Instructions

Digital Controller Functions

Cleaning and Maintenance

Troubleshooting

Wiring Diagram

Masterbuilt 1-Year Limited Warranty

Masterbuilt MWG 600B Specifications

General IconGeneral
BrandMasterbuilt
ModelMWG 600B
TypeElectric Smoker
Fuel TypeElectric
Voltage120V
Digital Control PanelYes
Built-in Meat ProbeYes
Wood Chip TrayYes
Water PanYes
Cooking Area600 square inches
Temperature Range100°F to 275°F
Number of Burners1

Related product manuals