MAXA i-32V5 - Page 41

To Previous Page

i-32V5

ADVANTIX SpA

Via S. Giuseppe Lavoratore 24,

37040 Arcole (VR) Italy

Tel. (+39).045.76.36.585

E-mail: info@advanxspa.it

www.maxa.it

Main Page

Table of Contents3
How to Keep the Manual6
Graphic Symbols Used in the Manual6
Permitted Used6
General Safety Guidelines6
Personal Protective Equipment6
Workers' Health and Safety6
Purpose and Contents of the Manual8
User Interface - Controller9
Menu9
Setpoint Menu9
Password Menu [Pss]10
PROBES MENU [Tp]10
ALARMS MENU [Err]10
DIGITAL INPUTS MENU [ID]10
PARAMETERS MENU [Par]10
OPERATING HOURS MENU [Ohr]11
MENU VERSIONE FIRWARE [Fir]11
LOG MENU [Hist]11
Usb Menu [Usb]11
Firmware Update [Updf]11
Parameters Update [Uppa]11
Display11
Led12
Terminal Block12
Editing Dynamic Set-Point13
Settings for Standard Climatic Curves13
Edit the Set-Point from 0-10V Input or from Ratiometric Input14
Circulator14
CONTINUOUS OPERATION [P03=0] - Default15
Operation on Call by Temperature Controller [P03=1]15
Operating on Call by Temperature Controller with Periodic Activation15
Operation with Heater Active15
Proportional Regulation of the Circulator15
System Venting16
Compressor or Activation Logic16
Regulation in Cooling Mode16
Regulation in Heat Mode16
Dissipation Fan Control17
Silenced Ventilation17
Controller Functions17
Antifreeze Protection Heaters (if Ka Accessory Is Available)17
Enabling Domestic Hot Water Production17
Memorising the Probe in Heating Mode18
Heating Mode on Dhw Storage Tank18
Insufficient Heat Exchange in a Dhw System18
Remote-Controlled Functions18
On/Off18
Summer/Winter Mode Change19
Dhw Call from Digital Input19
System Water Remote Probe19
Auxiliary Heaters19
Plant Heater19
Plant Heater in Defrost20
Dhw Heater20
Single Plant/Dhw Integration Heater20
Integration Heater Selection Mode20
Circulator Management with Heater on20
Boiler Enabling20
Activation of Integration Heaters and Boiler in Joint Operation and in Substitution of Heat Pump Compressor21
Operation in Heat Pump Mode21
Joint Operation (I Bracket)21
Joint Operation (II Bracket)21
Operation in Substitution22
Operating Brackets - Activation of Integration Heaters (Plant Remote Water Probe Not Enabled)22
Auxiliary Systems Offset Management25
Warnings25
Plant Season25
Alarm25
Machine Block25
Defrost25
Defrost Cycle25
Compressor Crankcase Heater26
Double Set-Point26
Minimum Hz Functionality26
Maximum Hz Functionality26
Flowmeter26
Functions that Can be Activated with Hi-T2 Accessory (Optional)27
Functions that Can be Activated with Gi Module (Optional)27
I/O Resources of the Controller27
Management of Secondary Circulator/Booster Pump (with Room Thermostat)28
Mixer Valve Management28
Determination of Setpoint28
Radiant Panels Circuit Pump28
Mixer Valve28
Solar Integration Management29
Activation of Solar Circulator29
Collector Protection29
Collector Overtemperature Alarm29
Dhw Overtemperature Alarm29
Solar Exhaust Valve29
Dissipation of Solar Tank Heat29
Antifreeze29
Tables of Permitted Setups for User and Installer30
Alarms33
E006] Flow Switch34
E018] High-Temperature34
E020] Inverter Trasductors34
E005] Antifreeze34
E611÷E681] Probe Alarms34
E801] Timeout Inverter34
E851 ÷E971] Inverter34
E00] Remote On/Off (Warning)34
E001] High-Pressure34
E002] Low-Pressure34
Power Failure35
Utilities Block Alarm Table35
Modbus Variables35

MAXA i-32V5 - Page 41

Table of Contents

Other manuals for MAXA i-32V5

Related product manuals