EasyManua.ls Logo

Mec 4046SE - default chapter; Table of Contents

Default Icon
176 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Page ii SE
AC
Slab Series - Service & Parts Manual
March 2022
Table of Contents
Chapter 1 - Service . . . . . . . . . . . . . 1
Service Introduction
. . . . . . . . . . . . . . . . . 1
Section 1 - MEC Operator Policy
. . . . . . . . . . . . . 2
MEC Operator Policy . . . . . . . . . . . . . . . . . . . 2
Section 2 - Safety Symbols & General Safety Tips . . . . . . . . 3
Safety Symbols & General Safety Tips . . . . . . . . . . . . . . 3
Section 3 - Specifications . . . . . . . . . . . . . . . 4
Specifications - 1930SE, 2632SE, 3346SE . . . . . . . . . . . . . 4
Specifications - 4046SE, 4555SE . . . . . . . . . . . . . . . . 5
Section 4 - Torque Specifications . . . . . . . . . . . . . 6
Bolt Torque Specification - American Standard . . . . . . . . . . . . 6
Bolt Torque Specification - Metric Standard . . . . . . . . . . . . . 7
Hydraulic Components Torque Table . . . . . . . . . . . . . . . 8
Section 5 - Maintenance Locks. . . . . . . . . . . . . . 9
Maintenance Locks - 1930SE, 2632SE, 3346SE . . . . . . . . . . . . 9
Maintenance Locks - 4046SE, 4555SE . . . . . . . . . . . . . . 10
Section 6 - Hydraulic System, Electrical System and Total System . . . . 12
Hydraulic System, Electrical System and Total System . . . . . . . . . . 12
Section 7 - Primary Machine Components. . . . . . . . . . . 13
Primary Machine Components . . . . . . . . . . . . . . . . 13
Section 8 - Emergency Systems and Procedures. . . . . . . . . 14
Emergency Systems and Procedures . . . . . . . . . . . . . . . 14
Section 9 - Transport and Lifting Instructions. . . . . . . . . . 15
Free-Wheel Configuration for Winching or Towing . . . . . . . . . . . 15
Driving or Winching onto or off of a Transport Vehicle. . . . . . . . . . . 16
Lift and Support the Machine . . . . . . . . . . . . . . . . . 18
Section 10 - Maintenance . . . . . . . . . . . . . . . 19
Machine Maintenance – General . . . . . . . . . . . . . . . . 19
Pre-Start Inspection Checklist . . . . . . . . . . . . . . . . . 20
Frequent Inspection Checklist . . . . . . . . . . . . . . . . . 21
Calibration Instructions . . . . . . . . . . . . . . . . . . 31
Annual Inspection Checklist . . . . . . . . . . . . . . . . . 33
Section 11 - Control Component Locations . . . . . . . . . . 36
Control Component Locations. . . . . . . . . . . . . . . . . 36
Section 12 - Fault Codes . . . . . . . . . . . . . . . 37
Fault Codes . . . . . . . . . . . . . . . . . . . . . 37

Table of Contents

Other manuals for Mec 4046SE

Related product manuals