To Next PageTo Next PageHow to reset factory setting parameter list on Meiko EcoStar 530 F-M?
To set parameters back to factory settings on your Meiko Dishwasher, switch the power supply OFF and then ON within 5 minutes.
Why does my Meiko Dishwasher say 'Emergency program active Restricted washing possible'?
If the Meiko Dishwasher displays 'Emergency program active Restricted washing possible,' it indicates an issue with either the boiler/tank heating or the fresh water supply. Check the system to identify the exact cause.
What does 'Regeneration in progress' mean on my Meiko Dishwasher?
The Meiko Dishwasher regeneration program has started and is currently running. You can pause the program, but you cannot cancel it.
What to do if my Meiko EcoStar 530 F-M Dishwasher says 'Regeneration necessary'?
The Meiko Dishwasher requires regeneration. The user must start the regeneration by emptying the tank and adding salt.
What to do if the hood of my Meiko EcoStar 530 F-M Dishwasher is not closed?
If the hood of the Meiko Dishwasher is not closed, check the connection S1, change the microswitch, check the microswitch adjustment or replace the defective I/O circuit board.
What to do if my Meiko Dishwasher says 'Incorrect password / no authorization'?
If you enter an incorrect password or lack authorization on the Meiko Dishwasher, enter the code once again.
Why does my Meiko EcoStar 530 F-M Dishwasher say maintenance is required?
Your Meiko Dishwasher indicates that maintenance is required because the set operating hours (P122) or batch number (P123) has been reached. Inform the service department and perform maintenance. After maintenance, reset the maintenance counter (P124).
What to do if my Meiko EcoStar 530 F-M Dishwasher hood is not closed?
If the hood of your Meiko Dishwasher is not closed, you should check connection S1, check the microswitch adjustment, change the microswitch or replace a defective I/O circuit board.
What to do if my Meiko EcoStar 530 F-M asks for factory setting parameter list?
To address the 'Factory setting parameter list' message on your Meiko Dishwasher, switch the power supply ON/OFF within 5 minutes and set parameters back to factory settings. This action will be rejected, and parameters will be retained and Information 123 will disappear.
How to resolve the 'Incorrect password / no authorization' error on my Meiko EcoStar 530 F-M?
To resolve the 'Incorrect password / no authorization' error on your Meiko Dishwasher, enter the code once again.
General| Water consumption | 2.6 l/cycle |
|---|---|
| Place settings | 13 |
| Noise level | 49 dB |
| Dimensions (W x D x H) | 600 x 600 x 1440 mm |
| Dimensions (H x W x D) | 1440 x 600 x 600 mm |
Outlines the operator's responsibilities for ensuring safe machine operation and maintenance.
Details essential safety precautions for operating the dishwashing machine, including electrical and water hazards.
Guidelines for safely moving, installing, and assembling the machine, including leveling and sealing.
Specifies required conditions for installation and operation, such as frost-free areas and proper connections.
Details specifications for electrical hook-up, including voltage, grounding, and cable requirements.
Steps and safety precautions to be followed by qualified personnel during the initial setup and commissioning of the appliance.
Emphasizes the importance of regular care and maintenance for reliable and hygienic operation.
Explains how to navigate and use the keyboard for programming and accessing different user levels.
Details the procedure for entering access codes to unlock various functions and parameter levels.
Describes how to access and navigate the service level for viewing and modifying parameters.
A comprehensive list of all adjustable parameters, their use, range, and factory settings.
Guides users on how to interpret information codes displayed by the machine for troubleshooting.
Lists common error messages, their possible causes, and suggested troubleshooting steps.
Highlights essential safety precautions to be observed before and during maintenance activities.
A detailed schedule of maintenance procedures and checks for various machine components.
