Why does my Meiko Dishwasher say maintenance is required?
Your Meiko Dishwasher indicates that maintenance is required because the set operating hours (P122) or batch number (P123) has been reached. Inform the service department and perform maintenance. After maintenance, reset the maintenance counter (P124).
What does 'regeneration in progress' mean on my Meiko Dishwasher?
The regeneration program for the Meiko Dishwasher has started and is currently in progress. You can pause the process, but it is not possible to cancel it.
Why does my Meiko Dishwasher say 'Refill with salt'?
If the Meiko Dishwasher displays 'Refill with salt,' it indicates one of two issues: either the salt supply is depleted, or there is no water in the salt solution reservoir and the float switch S5 is not working. Check the salt supply and the functionality of the float switch S5.
How to fix a Meiko Dishwasher when the door is not closed?
The Meiko Dishwasher door is not closed properly. You should check the connection S1, change the microswitch, check the microswitch adjustment or consider replacing a defective I/O circuit board.
What does it mean when my Meiko FV 40.2 says 'Regeneration is not possible as no salt available'?
The Meiko Dishwasher regeneration process requires brine, but none is available. This means regeneration is necessary, but cannot proceed without brine.
What does 'Emergency program active' mean on my Meiko FV 40.2?
If your Meiko Dishwasher displays 'Emergency program active,' it indicates that there is no boiler or tank heating. Check system.
What to do if Meiko Dishwasher says refill with salt?
If your Meiko Dishwasher indicates 'Refill with salt', it means there is no brine available. Check the salt supply and ensure there is water in the salt solution reservoir. Also, check if the float switch S5 is working.
What to do if Meiko FV 40.2 Dishwasher shows error in the dosing system ADT?
If you see an error in the ADT dosing system of your Meiko Dishwasher, it indicates that the flow meter is recognizing impulses even when detergent dosing is not in progress. This can happen if the valve of the dosing unit is not closing. In that case, you should check the valve of the dosing unit.
What to do if my Meiko Dishwasher says 'Incorrect password / no authorization'?
If you enter an incorrect password or lack authorization on the Meiko Dishwasher, enter the code once again.
What to do if my Meiko Dishwasher says 'Regeneration necessary'?
The Meiko Dishwasher requires regeneration. The user must start the regeneration by emptying the tank and adding salt.
Specifies the authorized commercial applications for the dishwasher.
Lists prohibited uses and materials that must not be processed in the machine.
General safety guidelines and precautions for operating the dishwasher.
Procedures to follow in dangerous situations, including power disconnection.
Describes the location and meaning of safety labels affixed to the dishwasher.
Outlines qualifications and responsibilities for operating and maintaining the machine.
Discusses the use, types, and dosing of detergents and rinse aids.
Specifies environmental and physical conditions needed for installation.
Details pipe size, height, and trap requirements for drainage.
Outlines water quality, hardness, temperature, and pressure specifications.
Covers voltage, current, wiring, and connection safety for power supply.
Instructions for safely connecting the dishwasher to the electrical power supply.
Steps for initial startup and verification of machine functions.
Troubleshooting guide for common issues and error messages.
General| Rack size | 500 x 500 mm |
|---|---|
| Total connected load | 6.8 kW |
| Entry height | 315 mm |
| Connected load | 6.8 kW |
| Tank capacity | 11 liters |
| Power supply | 3N PE 400V 50Hz |
| Theoretical capacity | 40 racks/h |
| Boiler heating | 6 kW |
| Tank heating | 2 kW |
| Boiler capacity | 6 l |
| Programs | Multiple programs including Eco, Intensive, Quick |
| Cycle time | 90 / 120 / 180 s |
| Programme cycle times | 90 / 120 / 180 s |
To Next Page
