To Next Page
D
Daniel MedinaAug 21, 2025
How to reset factory setting parameter list on Meiko FV 40.2?
- GgrantalexanderAug 21, 2025
To set parameters back to factory settings on your Meiko Dishwasher, switch the power supply OFF and then ON within 5 minutes.
How to reset factory setting parameter list on Meiko FV 40.2?
To set parameters back to factory settings on your Meiko Dishwasher, switch the power supply OFF and then ON within 5 minutes.
What to do if my Meiko Dishwasher says 'Regeneration necessary'?
The Meiko Dishwasher requires regeneration. The user must start the regeneration by emptying the tank and adding salt.
Why does my Meiko FV 40.2 Dishwasher say 'Emergency program active Restricted washing possible'?
If the Meiko Dishwasher displays 'Emergency program active Restricted washing possible,' it indicates an issue with either the boiler/tank heating or the fresh water supply. Check the system to identify the exact cause.
What to do if I get an 'incorrect password' message on my Meiko Dishwasher?
To address an incorrect password or authorization issue on your Meiko Dishwasher, enter the code once again.
What does error in the dosing system ADT mean for Meiko FV 40.2?
The impulses of the flow meter are recognized, although the detergent dosing is not approached and the valve of the dosing unit is not closing.
Why is the emergency program active on my Meiko FV 40.2?
An emergency program is active on the Meiko Dishwasher, which restricts washing capabilities. This is due to either no boiler/tank heating or no fresh water supply. You should check the system.
What does it mean when my Meiko FV 40.2 says 'Regeneration is not possible as no salt available'?
The Meiko Dishwasher regeneration process requires brine, but none is available. This means regeneration is necessary, but cannot proceed without brine.
How to fix a Meiko Dishwasher when the door is not closed?
The Meiko Dishwasher door is not closed properly. You should check the connection S1, change the microswitch, check the microswitch adjustment or consider replacing a defective I/O circuit board.
Why does my Meiko Dishwasher say 'Refill with salt'?
If the Meiko Dishwasher displays 'Refill with salt,' it indicates one of two issues: either the salt supply is depleted, or there is no water in the salt solution reservoir and the float switch S5 is not working. Check the salt supply and the functionality of the float switch S5.
What does 'regeneration in progress' mean on my Meiko Dishwasher?
The regeneration program for the Meiko Dishwasher has started and is currently in progress. You can pause the process, but it is not possible to cancel it.
Specifies the authorized commercial applications for the dishwasher.
Lists prohibited uses and materials that must not be processed in the machine.
General safety guidelines and precautions for operating the dishwasher.
Procedures to follow in dangerous situations, including power disconnection.
Describes the location and meaning of safety labels affixed to the dishwasher.
Outlines qualifications and responsibilities for operating and maintaining the machine.
Discusses the use, types, and dosing of detergents and rinse aids.
Specifies environmental and physical conditions needed for installation.
Details pipe size, height, and trap requirements for drainage.
Outlines water quality, hardness, temperature, and pressure specifications.
Covers voltage, current, wiring, and connection safety for power supply.
Instructions for safely connecting the dishwasher to the electrical power supply.
Steps for initial startup and verification of machine functions.
Troubleshooting guide for common issues and error messages.
General| Rack size | 500 x 500 mm |
|---|---|
| Total connected load | 6.8 kW |
| Entry height | 315 mm |
| Connected load | 6.8 kW |
| Tank capacity | 11 liters |
| Power supply | 3N PE 400V 50Hz |
| Theoretical capacity | 40 racks/h |
| Boiler heating | 6 kW |
| Tank heating | 2 kW |
| Boiler capacity | 6 l |
| Programs | Multiple programs including Eco, Intensive, Quick |
| Cycle time | 90 / 120 / 180 s |
| Programme cycle times | 90 / 120 / 180 s |
