Mercury Sea Pro

To Next Page

To Previous Page

OPERATION

ob01449

6. If engine is cold, hold the fuel primer button in and pump up the fuel pressure with the fuel primer bulb.

ob01649

7. Pull the starter rope to start the engine.

Main Page

Table of Contents3
Transfer of Warranty6
Warranty Registration United States and Canada6
Warranty Registration Outside the United States and Canada6
Warranty Information6
Mercury Marine Two Years Limited Warranty (Europe)7
Mercury Marine One Year Limited Warranty (Confederation of Independent States, Middle-East, Africa)8
Year Limited Warranty against Corrosion10
Warranty Coverage and Exclusions11
Boater's Responsibilities13
Before Operating Your Outboard13
Boat Horsepower Capacity13
General Information13
High-Speed and High-Performance Boat Operation14
Outboard Remote Control Models14
Remote Steering Notice14
Lanyard Stop Switch15
Protecting People in the Water16
Passenger Safety Message - Pontoon Boats and Deck Boats16
Wave and Wake Jumping17
Impact with Underwater Hazards18
Safety Instructions for Hand Tilled Outboards19
Exhaust Emissions19
Selecting Accessories for Your Outboard20
Safe Boating Suggestions21
Recording Serial Number21
55/60 Seapro/Marathon - 60 HP Specifications22
60 Component Identification23
55/60 Seapro/Marathon Component Identification24
Installing Outboard25
Installation25
Propeller Selection26
Trailering Boat/Outboard27
Transporting27
Gasoline Recommendations28
Oil Recommendation28
Fuel and Oil Ratio28
Fuel & Oil28
Filling Oil Injection System29
Filling Remote Oil Tank (if Equipped)29
Filling Fuel Tank30
Remote Control Features31
Warning System31
Features & Controls31
Low Oil Level32
Engine Over-Speed Limiter33
Power Trim and Tilt (if Equipped)33
- Power Trim Operation34
- Auxiliary Tilt Switch35
- Shallow Water Operation35
- Tilting Outboard36
Manual Tilt System36
Throttle Grip Friction Adjustment - Tiller Handle Models38
Steering Friction Adjustment - Tiller Handle Models39
Trim Tab Adjustment39
Pre-Starting Check List41
Operating in Freezing Temperatures41
Operating in Salt Water or Polluted Water41
Operating at High Elevations41
Engine Break-In Procedure41
Operation41
Starting the Engine42
Gear Shifting45
Stopping the Engine46
Emergency Starting46
Outboard Care49
EPA Emissions49
Maintenance49
Inspection and Maintenance Schedule50
Flushing the Cooling System50
Top Cowl Removal and Installation51
Battery Inspection52
Fuel System52
- Sea Pro/Marathon Models53
- Engine Idle Speed Adjustment54
- Fuel Line Inspection54
- Carburetor Adjustments54
Steering Link Rod Fasteners55
Fuse Replacement56
Corrosion Control Anode57
Propeller Replacement - 87.3 MM (3 - 7/16 In.) Diameter Gearcase58
Propeller Replacement - 108 MM (4 - 1/4 In.) Diameter Gearcase60
Spark Plug Inspection and Replacement62
Lubrication Points63
Lubrication Points - Sea Pro/Marathon Models65
Draining Gearcase66
Checking Power Trim Fluid66
Gearcase Lubrication66
Submerged Outboard68
Storage Preparation69
Protecting External Outboard Components69
Protecting Internal Engine Components69
Gearcase69
Positioning Outboard for Storage69
Storage69
Battery Storage70
Starter Motor will Not Crank the Engine (Electric Start Models)71
Engine will Not Start71
Engine Runs Erratically71
Performance Loss71
Troubleshooting71
Battery will Not Hold Charge72
Local Repair Service73
Service Away from Home73
Parts and Accessories Inquiries73
Service Assistance73
Mercury Marine Service Offices73
Owner Service Assistance73

Mercury Sea Pro - Page 48

Table of Contents

Related product manuals