What to do if my Metos LUX 60 EL Dishwasher does not load water?
If your Metos Dishwasher isn't loading water, check these potential causes: * Water valve: Ensure the hot and/or cold water valve is open. * Blocked nozzles or filter: Clean the rinse arm nozzles, piping, and solenoid-valve filter. Verify that the water hardness is less than 10°f. * Pressure switch: Replace the pressure switch if it's defective.
Why does my Metos LUX 60 EL suddenly stop during operation?
Your Metos Dishwasher might stop suddenly during operation due to: * Overload device: The machine may be connected to an overload device. Connect the machine on its own overload device. * Triggered safety device: A machine safety device may have been triggered.
How to remove streaks and spots from glasses and dishes in Metos LUX 60 EL Dishwasher?
Streaks and spots on glasses and dishes from your Metos Dishwasher can be due to: * Too much rinse-aid: Reduce the amount of rinse aid using the dispenser screw. * Hard water: Ensure your water hardness does not exceed 8°f. * Insufficient salt or regeneration (for softeners): Fill the salt container with coarse salt (1-2 mm grains) and regenerate the resins more often. If lime deposits are observed, have a technician check the softener. * Salt in the sump: Thoroughly clean and rinse the dishwasher, avoiding salt spillage when filling the container.
What to do if glasses or dishes are not drying properly in my Metos LUX 60 EL Dishwasher?
If your Metos Dishwasher leaves glasses or dishes not properly dried, consider the following: * Insufficient rinse aid: Increase the rinse aid dosage by adjusting the dispenser screw. * Unsuitable rack: Use a rack that allows water to rinse away easily. * Items sitting too long: Remove the rack as soon as the cycle stops to allow quicker air drying. * Low rinse temperature: Check that the boiler thermostat temperature is at least 80°C. * Dish surface issues: Replace overly rough or porous dishes. For dry, old dirt, soak dishes before washing.
Why does water drain very slowly from my Metos LUX 60 EL?
Slow draining in your Metos Dishwasher could be due to: * Low water supply pressure: Check the water supply pressure. * Blocked rinse booster pump: If your dishwasher has a rinse booster pump and it's blocked, call for service.
Why does the Metos LUX 60 EL stop during the wash stage and start refilling water?
The Metos Dishwasher stopping during the wash stage and refilling water can occur because: * Old water: The previous day's water was not changed. Drain the tank completely and refill it. * Excessive water temperature: The water temperature in the tank is too high. Call for Service to check thermostat and pressure-switch. * Defective pressure switch: No answer.
How to turn on Metos Dishwasher?
If your Metos Dishwasher doesn't turn on, the main switch might not be ON. Turn the switch ON.
Why are the washing results unsatisfactory with my Metos LUX 60 EL?
Unsatisfactory washing results with your Metos Dishwasher can stem from several causes: * Obstructed washing nozzles or the rack not rotating: Clean the nozzles carefully and ensure the wash-arm is correctly positioned and firmly tightened. * Foam presence: Use no-foam detergents or reduce the current detergent dosage; also, check the rinse-aid dosage. * Fats or starches not removed: This indicates insufficient detergent concentration. * Dirty filters: Remove the filters, clean them with a brush under running water, and replace them in their original positions. * Incorrect tank temperature: The tank temperature should be between 50°C and 60°C. Adjust the thermostat or check the heating element's operation. * Insufficient wash time: Select a longer wash cycle or repeat the curr...
Overview of the machine's physical components and layout.
Details on the machine's technical specifications and noise level.
Explanation of the control panel buttons, indicators, and displays.
Step-by-step guide for starting the machine for the first time.
Instructions on selecting and running a wash cycle.
Procedure for correctly shutting down and putting the machine into standby.
Guidance on selecting and using appropriate detergents for optimal washing.
Instructions on using rinse aid for drying and proper machine function.
Details on how to drain the wash tank, especially at the end of the day.
Steps for activating and performing the optional salt regeneration cycle.
How to enable and use the optional additional cooling function for rinsing.
Advice on efficient use of resources like water, energy, and detergents.
Daily cleaning procedures to keep the machine in perfect running order.
Periodic inspections and maintenance performed by qualified technicians.
Procedures for safely handling and moving the machine.
Specific instructions for lifting and transporting the appliance.
Guidelines for storing the machine before installation.
Preliminary steps and requirements before installing the machine.
Requirements for the installation room environment and temperature.
Technical specifications and local law compliance for electrical hookup.
Water supply requirements, hardness, and temperature specifications.
Ventilation requirements for the installation room to manage steam.
General steps and considerations for physically installing the machine.
Guidelines for placing the machine in its final location.
Detailed instructions for connecting the machine to the electrical supply.
How to connect the water inlet and drain hoses to the machine.
Final steps for starting the machine after installation.
Components of the packaging materials used for the product.
Guidelines for proper disposal of the product and its components.
General| Basket size | 500 x 500 mm |
|---|---|
| Water consumption/cycle | 2.5 liters |
| Electrical connection | 400 V, 3-phase |
| Type | Undercounter |
| Dimensions | 850x600x600 mm |
To Next Page