What to do if my Metos Dishwasher suddenly stops during operation?
If your Metos Dishwasher suddenly stops during operation, it could be connected to an overload device. Connect the machine to its own overload device (call Service). Alternatively, a machine safety device might have been triggered. Check the electrical devices (call Service).
Why does my Metos Dishwasher stop during the wash stage and start refilling water?
If your Metos Dishwasher stops during the wash stage and starts refilling water, it could be because the previous day's water wasn't changed. Drain the tank completely and refill it. Excessive water temperature in the tank could also be the cause. Call Service to check the thermostat and pressure-switch. Also, check if the overflow pipe is improperly positioned. If so, remove and reposition it correctly.
Why are there streaks and spots on my Metos Dishwasher glasses and dishes?
Streaks and spots on glasses and dishes can occur if there's too much rinse-aid chemical. Reduce the amount of rinse aid by adjusting the micrometric dispenser screw. Another reason is too hard water. Ensure the water does not exceed 8°f in hardness. For appliances with a softener, ensure there's enough salt in the salt container and that the resins are properly regenerated. Fill the salt container with coarse salt (1-2 mm grains) and regenerate the resins more often. If you notice lime deposits on the machine, have a qualified technician check the water softener. Also, salt present in the dishwasher sump can cause streaks. Thoroughly clean and rinse the appliance, avoiding spilling salt when filling the container.
Why are glasses or dishes not properly dried in my Metos Dishwasher?
If your Metos Dishwasher isn't drying glasses or dishes properly, it could be due to several reasons. You may not be using enough rinse aid; increase the dosage by turning the dispenser screw. The rack might not be suitable, so use a rack that allows water to rinse away easily. Also, removing the rack as soon as the cycle stops helps them dry more quickly. A rinse temperature below 80°C can also cause drying issues, so check the boiler thermostat temperature. Lastly, the surface of your dishes and glasses might be too rough or porous; consider replacing them or soaking items before washing if the dirt is dry and old.
What to do if my Metos Dishwasher does not load water?
If your Metos Dishwasher does not load water, it could be due to a shut water valve. Open the hot and/or cold water valve. Another potential cause is blocked rinse area nozzles or a solenoid-valve filter scaled with limestone. Clean the rinse arm nozzles, conductors, and solenoid-valve filter, and ensure the water hardness is less than 10°f. A defective pressure-switch can also prevent water loading. Replace the pressure-switch.
Why are the washing results unsatisfactory in my Metos Dishwasher?
If your Metos Dishwasher isn't cleaning dishes well, the washing nozzles might be blocked, or the rack isn't rotating. Clean the nozzles carefully and ensure the wash-arm is correctly positioned and tightened. Foam can interfere with washing, so use no-foam detergents or reduce the amount you're using, and check the rinse-aid dosage. Insufficient detergent concentration can prevent the removal of fats or starches. Ensure you are using enough detergent. Dirty filters can also cause poor washing results. Remove the filters, clean them with a brush under running water, and replace them correctly. The tank temperature should be between 50°C and 60°C, so adjust the thermostat or check the heating element. If the wash cycle isn't long enough, select a longer one or repeat the cycle. Finally, dir...
Добрый день! Вы можете нам прислать технический мануал для оборудования METOS WD-153 ICS
Explains the function of the control panel buttons, indicators, and display symbols.
Step-by-step guide for powering on, filling, heating, and initiating a wash cycle.
Daily cleaning procedures for filters, arms, and the tank to ensure proper operation.
Annual checks and maintenance tasks to be performed by qualified technicians.
Details on electrical connection requirements, safety switches, and voltage compatibility.
Specifications for water supply, including pressure, hardness, temperature, and drain connection.
Detailed instructions for connecting the machine to the electrical supply, including safety measures.
General| Brand | Metos |
|---|---|
| Model | HOOD 130S |
| Category | Dishwasher |
| Language | English |
To Next Page