Need help?Do you have a question about the Meyer Sound RMServer and is the answer not in the manual?
General| Storage | 64 GB SSD |
|---|---|
| Network Connectivity | Gigabit Ethernet |
| Height | 1U |
| Operating System | Linux |
| Network Interface | 2 x 1000BASE-T |
| Dimensions | 1.72 x 19 x 9.5 inches |
| Connectors | 2 x RJ-45 |
Guide on how to read and use the manual effectively, including icons for notes, tips, and cautions.
Overview of the Compass RMS system, its components, and capabilities for monitoring loudspeakers.
Step-by-step workflow for configuring Compass RMS systems, including legacy system integration.
Introduction to RMServer, its role as a central component in the Compass RMS system.
Details on RMServer's front panel, rear panel, indicators, and their respective functions.
Procedures and options for installing and physically mounting the RMServer unit, including rack and wallmount kits.
Steps to connect RMServer to the RMS network and configure initial system settings.
Describes how to connect RMServer to power, a computer, and network devices like hubs or switches.
Instructions for accessing and configuring the RMServer via its web interface using various methods.
Defines maximum loudspeaker nodes, cable types, lengths, and network platform details for RMS.
Details on using twisted-pair cables, connectors, and limitations for RMS network cabling.
Guidance on using hubs and switches for building RMS network infrastructure.
Best practices and tips for designing robust and efficient RMS network layouts, including cable management.
Illustrates various basic Ethernet configurations for Compass RMS systems.
Step-by-step guide for installing the HP/MP RMS module into compatible loudspeakers.
Instructions for installing the Mute Jumper to enable mute and solo capabilities on the module.
Overview of the HP/MP RMS module's user panel, including LEDs, buttons, and network connectors.
Information on the unique 12-character Neuron ID for identifying HP/MP RMS modules on the network.
Procedure for resetting the HP/MP RMS module and removing it from the RMServer inventory.
Detailed procedure for installing the UltraSeries RMS module into compatible loudspeakers.
Guide for installing the Mute Jumper to enable mute and solo functions on the module.
Explanation of the UltraSeries RMS user panel features, LEDs, and buttons.
Details on the unique Neuron ID for UltraSeries RMS modules and their network identification.
Steps to reset the UltraSeries RMS module and remove it from the RMServer inventory.
Procedure for installing the DX RMS module into compatible loudspeakers.
Overview of the DX RMS module's user panel, including Identify button, LEDs, and switches.
Information on the Neuron ID for DX RMS modules and their network identification.
Steps to reset the DX RMS module and remove it from the RMServer inventory.
Step-by-step guide to installing the MX RMS module in loudspeakers.
Instructions for installing the Mute Jumper on the MX RMS module for mute/solo.
Details about the Neuron ID for MX RMS modules and network identification.
Procedure for resetting the MX RMS module and removing it from the RMServer inventory.
Guide for installing the LYON RMS module into the LYON loudspeaker.
Information on the Neuron ID for LYON RMS modules and network identification.
Steps to reset the LYON RMS module and remove it from the RMServer inventory.
Overview of the MPS-488HP RMS user panel, including Identify button and LED.
Details on the Neuron ID for MPS-488HP RMS modules and network identification.
Procedure for resetting the MPS-488HP RMS module and removing it from the RMServer inventory.
How the MPS-488HP functions and is managed within the Compass RMS software.
A table comparing different RMS modules, their LEDs, buttons, connectors, and mute enable features.
Steps to verify your computer's IPv4 address for network troubleshooting.
How to check the RMServer's IPv4 address for network connectivity issues.
Guide on using the ping command to test network connectivity and identify issues.
Diagrams and instructions for wiring RMServer for external muting and warning relay functions.
Steps to configure RMServer for automatic muting via external relay closures.
How to set up RMServer's onboard relays for warning purposes based on failure conditions.
Configuration for receiving email alerts for external muting and warning relay events.
Instructions for physically mounting and installing the FTR-120 repeater.
How to configure network termination settings for the FTR-120 repeater.
Pin-out and wiring details for connecting the FTR-120 repeater.
To Next Page
