EasyManua.ls Logo

Mhouse MhouseKit WS2S - User Manual

Mhouse MhouseKit WS2S
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MhouseKit WS2
S
For power-operated swing gate
Installation instructions and warnings, and User Manual
IS0004A00EN 28-03-2011

Table of Contents

Questions and Answers

  • B
    bridgesspencerAug 14, 2025
    What to do if the Mhouse Gate Opener manoeuvre does not start and the flashing light flashes?
    • S
      Sean ParkerAug 14, 2025
      If your Mhouse Gate Opener manoeuvre doesn't start and the flashing light flashes, first ensure the STOP input isn't active by checking if the LED “STOP” [C] is illuminated. If it isn't, inspect the device connected to the STOP input. Also, a negative photocell test at the beginning of each manoeuvre could be the cause; in this case, inspect the photocells.
  • E
    Ellen OrrAug 17, 2025
    Why does my Mhouse Gate Opener manoeuvre start but is immediately followed by an inversion?
    • C
      Charles HarrisAug 17, 2025
      If your Mhouse Gate Opener manoeuvre starts but immediately reverses, the selected force might be too low to move the gate. Check for any obstructions and, if necessary, increase the force setting as described on page 21.
  • D
    Dominique WilsonAug 21, 2025
    What to do if the Mhouse MhouseKit WS2S Gate Opener manoeuvre does not start and the flashing light is off?
    • C
      Connie MillerAug 21, 2025
      If the Mhouse Gate Opener manoeuvre doesn't start and the flashing light is off, check that the command is actually being received. When the command reaches the OPEN input the relevant LED “OPEN” [D] should light up; if a radio transmitter is used the LED “ECSBus” should emit two long flashes.
  • C
    Connie HardingAug 25, 2025
    How to fix the flashing light when the Mhouse MhouseKit WS2S Gate Opener manoeuvre is carried out?
    • T
      Travis GreenAug 25, 2025
      If the Mhouse Gate Opener manoeuvre is carried out but the flashing light isn't working, check for voltage on the FLASH terminal of the flashing light during operation (approximately 10-30 Vac). If voltage is present, the lamp is likely faulty and should be replaced with an identical one.
  • K
    Kayla OrtegaAug 27, 2025
    What to do if the device not recognised by the Mhouse Gate Opener control unit?
    • J
      Julie PetersonAug 27, 2025
      If the Mhouse Gate Opener device is not recognised by the control unit, repeat the learning procedure on the control unit. Also, verify that all photocell pairs on ECSBus have different addresses as shown in Table 8.
  • D
    Diana GrahamAug 31, 2025
    How to fix Mhouse MhouseKit WS2S radio transmitter if it does not emit any signal?
    • W
      Wesley GrantAug 31, 2025
      If your Mhouse Gate Opener radio transmitter isn't emitting a signal (LED [A] doesn't light up), check if the batteries are flat and replace them if necessary, as detailed on page 36.
  • K
    kelly09Sep 2, 2025
    What to do if the Mhouse Gate Opener photocell is not powered or it is faulty?
    • K
      Katherine CampbellSep 2, 2025
      If the Mhouse Gate Opener photocell is not powered or seems faulty, check that the voltage on the photocell terminals is approximately 8-12 Vdc. If the voltage is correct, the photocell is likely faulty.
  • M
    Matthew CortezSep 6, 2025
    What to do if the Mhouse MhouseKit WS2S Gate Opener manoeuvre does not start and the LED “ECSBus” [B] does not flash?
    • J
      James VasquezSep 6, 2025
      If the Mhouse Gate Opener manoeuvre doesn't start and the LED “ECSBus” [B] doesn't flash, ensure the power supply cable is correctly inserted into the mains socket. Also, check that the fuses [E] and [F] haven't been activated; if they have, identify the cause of the fault and replace them with fuses of the same specifications.
  • J
    Jeremy CampbellSep 9, 2025
    What to do if the Mhouse Gate Opener RX does not receive any signal?
    • B
      Brandon WoodwardSep 9, 2025
      Check for any obstruction between TX and RX of Mhouse Gate Opener. Check that the LED on the TX flashes slowly. Check TX-RX alignment.

Summary

General Safety Warnings and Precautions

Safety Warnings

Critical safety instructions for users and installers of the automation system.

Installation Warnings

Guidelines and symbols for safe and correct installation procedures.

Operation Warnings

Precautions for safe operation, maintenance, and handling of the automation.

Product Knowledge and Preparation

Product Description and Intended Use

Details the WS2S system's purpose and application for swing gates.

Components for a Complete System

STEP 3: Preliminary Checks for Installation

Gate Suitability and Environment Checks

Verifies gate structure, movement, and installation environment for automation.

Product Application Limits

STEP 4: Installation Preparation

Device and Cable Positioning

Preparing Electric Cables

INSTALLATION: ASSEMBLY AND CONNECTION OF COMPONENTS

STEP 5: Installing the Gearmotor WS1 SC

Detailed step-by-step instructions for mounting the WS1SC gearmotor.

PROGRAMMING

STEP 6: Installing and Connecting Accessories

STEP 7: Programming Operations

Power Supply Connection

Procedure for connecting the automation to the main power supply.

Initial System Checks

Recognizing Connected Devices

Learning Gate Leaf Angles

Calibrating the system for gate leaf opening and closing limits.

STEP 8: Testing and Commissioning

System Testing Procedures

Performing operational tests to ensure safety and functionality.

Commissioning the Automation

Final steps for putting the automation into service and documentation.

FURTHER INFORMATION

10.4 Memorizing Radio Transmitters

10.5 Troubleshooting

Common malfunctions and their potential solutions.

10.6 Diagnostics and Signals

Control Unit Diagnostics

APPENDIX 1: CE Declaration of Conformity

USERS GUIDE

11.1 Safety Instructions

Essential safety guidelines for operating the automation.

11.2 Gate Control

11.3 Manually Releasing or Locking the Gearmotor

APPENDIX 2: CE Declaration of Conformity

Mhouse MhouseKit WS2S Specifications

General IconGeneral
Motor Voltage24 V DC
Protection ClassIP44
Obstacle DetectionYes
Manual ReleaseYes
Wireless Frequency433.92 MHz
Remote Control RangeUp to 30 m
Power Supply230 V AC

Related product manuals