To Next Page
K
Kelsey AllenAug 18, 2025
What to do if my Mi-T-M Pressure Washer unit components are frozen?
- NNicholas BurnettAug 18, 2025
If the components of your Mi-T-M Pressure Washer are frozen, allow them to thaw.
What to do if my Mi-T-M Pressure Washer unit components are frozen?
If the components of your Mi-T-M Pressure Washer are frozen, allow them to thaw.
What to do if my Mi-T-M Pressure Washer has no discharge at the nozzle?
If the Mi-T-M Pressure Washer isn't dispensing water when you squeeze the trigger, several factors could be at play. First, ensure your water supply is adequate by using a 3/4" diameter hose and verifying the water is turned on. Check for and remove any kinks in the high-pressure discharge hose. Inspect and clean or replace the water inlet screen if it's obstructed. Tighten all water intake connections to eliminate air leaks. Make sure the collar on the adjustable nozzle is set to high pressure by turning it clockwise. Finally, check for obstructions or wear in the spray nozzle, valve assembly, or pump packings, replacing or repairing as needed. If the unloader/bypass valve isn't working correctly, repair or replace it.
How to fix detergent siphoning problem in my Mi-T-M Pressure Washer?
If the detergent isn't siphoning into the low-pressure detergent mode on your Mi-T-M Pressure Washer, first ensure the detergent strainer is fully submerged in the solution. Inspect, clean, or replace the detergent strainer and hose if they are obstructed, cut, or kinked. Open the detergent adjusting knob. Make sure the collar on the adjustable nozzle is in the low-pressure mode by turning the collar counterclockwise. Clean or replace a plugged nozzle assembly. Use only one high-pressure hose extension maximum. Finally, remove, clean, or replace the ball & spring in the Venturi if stuck.
What to do if water is leaking from the 'Heat Dump Valve' of my Mi-T-M Pressure Washer?
If your Mi-T-M Pressure Washer is leaking water from the heat dump valve, it could be due to the water temperature being too high. Avoid operating the unit in bypass mode (with the trigger gun closed) for more than 3 minutes. If the issue persists, the valve may be defective and needs replacement.
Why does the oil in my Mi-T-M Pressure Washer look milky or foamy?
If the oil in your Mi-T-M Pressure Washer appears milky or foamy, it indicates water contamination. Change the pump oil and fill it to the correct level.
Why is my Mi-T-M Pressure Washer burner running erratically?
If the burner on your Mi-T-M Pressure Washer is running erratically, it could be due to water in the fuel oil. Drain the fuel tank and replace it with clean fuel. Also, consider replacing a dirty fuel filter or nozzle. If the problem continues, the fuel pump may be malfunctioning and require replacement.
What causes my Mi-T-M Pressure Washer burner to run, but not heat?
If the burner of your Mi-T-M Pressure Washer runs but doesn't heat, the issue might stem from a poor or improper fuel supply. Check the fuel to ensure it's correct. Drain the tank and filter if necessary, and refill with the proper fuel. Also, check the fuel pump pressure, replacing the pump if needed, and replace a dirty fuel nozzle.
Why is water flowing back into the detergent container of my Mi-T-M Pressure Washer?
If water flows back into the detergent container of your Mi-T-M Pressure Washer, the ball & spring in the Venturi may be reversed, missing, or corroded. Remove, clean, or replace these components.
Why is my Mi-T-M Pressure Washer burner discharging white smoke?
If your Mi-T-M Pressure Washer is discharging white smoke, it may be low on fuel. Refuel the unit. If the white smoke persists, consult your Customer Service.
What to do if my Mi-T-M Pressure Washer is leaking water under the heat exchanger coil?
If your Mi-T-M Pressure Washer is leaking water under the heat exchanger coil, it could be caused by an unloader or pressure switch problem. Detect and correct the unloader or pressure switch problem. Also, replace the safety relief device.
General| Model | GPH-2000-0M1R |
|---|---|
| Category | Pressure Washer |
| Engine | Mi-T-M OHV |
| Engine Displacement | 196cc |
| Pump | Axial Cam |
| PSI | 2000 |
| GPM | 2.0 |
| Hose Length | 25 ft |
| Power Source | Gasoline |
| Nozzle Included | Yes |
| Wheels | Yes |
| Nozzles | Quick Connect |
