Why will my Mi-T-M HS Pressure Washer engine not start?
If your Mi-T-M Pressure Washer engine won't start, the issue may stem from engine problems or frozen components. Refer to the Engine Manual included with your unit for engine-specific troubleshooting. If any part of the unit is frozen, allow it to thaw completely before attempting to start it. Freezing can cause excessive pressure buildup, potentially leading to serious injury.
What to do if my Mi-T-M Pressure Washer has low or fluctuating pressure?
If your Mi-T-M Pressure Washer exhibits low or fluctuating pressure, several factors could be responsible. Check for kinks in the water inlet hose and remove them. Inspect the water inlet screen for obstructions, and clean or replace it if necessary. Ensure all water intake connections are tightened to eliminate air leaks. Replace with a high pressure nozzle, or move the adjustable grip on the dual lance counterclockwise to high pressure. Also, examine the spray nozzle and valve assembly for obstructions or damage, cleaning or replacing as needed. If the pump packings are worn, replace them. Finally, check the unloader/bypass valve for proper operation; repair or replace it if necessary.
What to do if the detergent will not siphon on my Mi-T-M Pressure Washer?
If the detergent is not siphoning in your Mi-T-M Pressure Washer, ensure the detergent strainer is fully submerged in the detergent solution. Check the strainer, hose, and nozzle assembly for any obstructions, cleaning or replacing them as needed. Also, verify that the detergent adjusting knob is in the open position. Refer to "Cleaning w/ Detergents" for more information.
What to do if water is leaking at the safety relief valve on my Mi-T-M HS Pressure Washer?
If water leaks from the safety relief valve on your Mi-T-M Pressure Washer, it indicates a potential issue with the unloader, pressure switch, or the safety relief valve itself. You should detect and correct any unloader or pressure switch problems. If the safety relief valve is defective, replace it immediately. Never operate the unit without a functional safety relief valve, as this can lead to an explosion.
Why is my Mi-T-M HS pump oil milky or foamy?
If the pump oil in your Mi-T-M Pressure Washer appears milky or foamy, it indicates water contamination. To resolve this, change the pump oil and refill it to the correct level.
What to do if my Mi-T-M HS burner runs erratically?
If your Mi-T-M Pressure Washer burner runs erratically, it could be due to several reasons: water in the fuel oil, a dirty fuel filter or fuel water separator, a dirty fuel nozzle, an improper air adjustment setting, or a malfunctioning fuel pump. Replace the fuel filter or drain the fuel water separator, drain the fuel tank and replace with clean fuel. Replace the fuel filter element and the fuel nozzle. Adjust the air and replace the fuel pump.
Why is there no discharge at the nozzle when I squeeze the trigger on my Mi-T-M HS Pressure Washer?
If there's no discharge at the nozzle when you squeeze the trigger on your Mi-T-M Pressure Washer, the cause might be an inadequate water supply. Make sure the hose is 3/4" in diameter and the incoming water supply is turned on.
Why does my Mi-T-M HS burner discharge white smoke?
If your Mi-T-M Pressure Washer burner discharges white smoke, it could be due to low fuel or an excessive air supply. Refuel the unit. If the white smoke persists, consult the Service Department. Adjust the air supply.
What to do if my Mi-T-M HS Pressure Washer blower motor will not run?
If the blower motor of your Mi-T-M Pressure Washer fails to run (and the burner cannot ignite without it), it may be due to a generator or burner/blower motor malfunction, or a broken or slipping belt on the generator. You may need to repair or replace the generator or burner/blower motor. If the belt is broken or slipping, adjust or replace it as necessary.
What to do if my Mi-T-M Pressure Washer burner discharges black smoke?
If your Mi-T-M Pressure Washer burner discharges black smoke, it indicates an insufficient air supply. Adjust the air supply to correct this issue.
Details risks associated with fuel handling, sparks, and flammable materials.
Warns about the dangers of carbon monoxide from engine exhaust in enclosed areas.
Covers hazards from high-pressure spray penetrating skin and sharp components.
Highlights dangers of contact with electricity and electrical installations.
Addresses risks from hot surfaces, freezing temperatures, and component bursting.
Covers injury from detergents, propelled debris, and loss of balance.
Steps for starting the engine and operating the unit with cold water.
Instructions for activating the burner and operating the unit with hot water.
Steps to properly turn off the pressure washer and cool down components.
Addresses engine start-up issues, fuel leaks, and fuel supply problems.
Covers no discharge, low/fluctuating pressure, water leaks, and hose issues.
General| Brand | Mi-T-M |
|---|---|
| Model | HS SERIES |
| Category | Pressure Washer |
| Language | English |
To Next Page