EasyManua.ls Logo

Mi-T-M HS-3008-1MGK - User Manual

Mi-T-M HS-3008-1MGK
86 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operator's Manual 1©Copyright 2006 Form #37-0741-E/F/S-052623
CAUTION
RISK OF INJURY!
READ MANUAL BEFORE OPERATING!
This manual is an important part of the pressure washer and must
remain with the unit when you sell or rent it!
OPERATOR'S MANUAL FOR
STATIONARY
GASOLINE DRIVEN/BELT DRIVE
OIL HEATED
HOT WATER
PRESSURE WASHERS
PARTS LIST

Table of Contents

Questions and Answers

  • T
    Timothy HarveyAug 14, 2025
    Why does my Mi-T-M HS-3008-1MGK Pressure Washer burner run erratically?
    • C
      Christopher MilesAug 15, 2025
      If the burner on your Mi-T-M Pressure Washer runs erratically, it could be due to: * Water in the fuel oil: Replace the fuel filter or drain the fuel water separator, drain the fuel tank and replace it with clean fuel. * A dirty fuel filter or fuel water separator: Replace the element. * A dirty fuel nozzle: Replace the fuel nozzle. * An improper air adjustment setting: Adjust the air adjustment. * A malfunctioning fuel pump: Replace the fuel pump.
  • L
    Larry DavenportAug 20, 2025
    What to do if Mi-T-M Pressure Washer blower runs, but burner will not ignite?
    • M
      Michael MillerAug 20, 2025
      If the blower runs on your Mi-T-M Pressure Washer, but the burner won't ignite, consider these possible causes: * Dirty or clogged fuel filter or fuel water separator: Drain or replace as necessary. * Low fuel pump pressure: Check fuel pump pressure, adjust or replace as necessary. * Fuel pump inoperative: Check pressure, replace if necessary. * Flexible coupler broken: Replace the coupler. * Fuel solenoid valve failure: Replace the valve. * Dirty or clogged fuel nozzle: Replace the fuel nozzle. * Improper burner air adjustment: Adjust the burner air. * Faulty ignition module: Repair or replace. Consult your Customer Service. * Ignition electrodes damaged or worn: Adjust or replace electrodes. Consult your Customer Service.
  • M
    Michelle PattersonAug 25, 2025
    Why is my Mi-T-M Pressure Washer burner discharging white smoke?
    • S
      Sally HernandezAug 26, 2025
      If your Mi-T-M Pressure Washer burner is discharging white smoke, it could be due to: * Low fuel: Refuel. If white smoke persists consult the Service Department. * Excessive air supply: Adjust the air supply.
  • R
    richard30Aug 30, 2025
    Why won't my Mi-T-M Pressure Washer burner heat up even though it ignites?
    • R
      Ryan BarnettAug 30, 2025
      If the burner on your Mi-T-M Pressure Washer ignites but doesn't heat, check the following: * Thermostat knob is OFF: Check thermostat knob position. * Detergent valve is open, but detergent hose is not completely submerged in solution: Close the valve, or completely clear vinyl hose into detergent solution. * Poor or improper fuel supply: Check fuel to ensure it is correct. Drain tank and filter if necessary and refill with proper fuel. * Dirty or clogged fuel filter or fuel water separator: Drain or replace as necessary. * Low fuel pump pressure: Check fuel pump pressure, adjust or replace if needed. * Dirty or clogged fuel nozzle: Replace fuel nozzle. * Improper burner air adjustment: Adjust. * Scale build up in heat exchanger coil: Consult the Service Department.
  • D
    Dean SmithSep 3, 2025
    Why is my Mi-T-M Pressure Washer burner discharging black smoke?
    • J
      Jessica DouglasSep 3, 2025
      If your Mi-T-M Pressure Washer burner is discharging black smoke, it's likely due to an insufficient air supply. Adjust the air supply to resolve this issue.
  • J
    jamie22Nov 9, 2025
    What to do if the Mi-T-M Pressure Washer blower motor will not run?
    • D
      Daniel YoungNov 9, 2025
      If the blower motor of your Mi-T-M Pressure Washer doesn't run (and the burner won't ignite without it), there are several potential causes: * A generator malfunction: Repair or replace the generator. * A burner/blower motor malfunction: Repair or replace the burner/blower motor. * A broken or slipping belt on the generator: Adjust or replace the belt. * The burner switch is not turned on: Check the switch position. * The thermostat knob is OFF: Check the thermostat knob position. * The trigger gun is closed: Open the gun for pressure. * Out of fuel: Refuel. * The detergent valve is open, but the detergent hose is not completely submerged in the solution: Close the valve or completely submerge the clear vinyl hose into the detergent solution. * Pressure switch override: ...

Mi-T-M HS-3008-1MGK Specifications

General IconGeneral
EngineMi-T-M OHV
Engine Displacement389cc
Pump TypeTriplex Plunger
PSI3000
Power SourceGasoline
Hose Length50 feet
Engine TypeOHV

Related product manuals