20
Operating
Instructions
Wireless operation(on some models)
Used to initiate the wireless connection mode. For the
first time to use wireless function, press the POWER
button for 3 seconds to initiate the wireless connection
mode . The LED DISPLAY shows 'AP' to indicate you can
set wireless connection. If connection(router) is success-
ful within 8 minutes, the unit will exit wireless connection
mode automatically and the wireless indicator illumi-
nates.
If connection is failure within 8 minutes, the unit exits
wireless connection mode automatically. After Wireless
connection is successful, for some models you can press
MODE and UP (+) buttons at the same time for 3 seconds
to turn off Wireless function and the LED DISPLAY
shows 'OF' for 3 seconds, press MODE button and UP(+)
to turn on Wireless function and the LED DISPLAY shows
'On' for 3 seconds.
NOTE: When you restart the wireless function, it may
take a period of time to connect to the networkauto-
matically.
This feature can be activated from the remote control
ONLY. To activate SLEEP feature, the set temperature
will increase(cooling) or decrease(heating) by 1°C/2°F
(or 1°F) in 30 minutes. The set temperature will then
increase(cooling) or decrease(heating) by another 1°C
Constatnt Fan button(On some models)
In cooling or Dry mode, press the button
for 3 seconds to turn on or off the constant
fan function. When the function is turned
on, the constant fan light will illuminate,
identifying the fan continuous run for cool-
ing. When the function is turned off, the
constant fan light will go out, identifying
the fan cycle run with compressor stop.
CONSTANT FAN(Press 3s)
VENT CONSTANT(Presse 3s)
FRESH operation(on some models)
Press MODE and DOWN (-) buttons at the same
time for 3 seconds to initiate FRESH feature and the
FRESH light illumiantes on some models, the LED
DISPLAY shows 'On' for 3 seconds. The ion genera-
toris energized and will help to purify the air inside.
Press it for 3 seconds again to stop the FRESH
feature and the FRESH light turn dark on some
models, the LED DISPLAY shows 'OF' for 3 seconds
for some units.
SLEEP/ECO operation
NOTE:Keep windows and doors closed for the
best dehumidifying effect.
DRY operation
•
•
Press the "MODE" button until the "DRY" indica-
tor light comes on.
The fan speed or the temperature cannot be
adjusted. The fan motor operates at LOW speed.
(on some models)
FAN operation
•
•
•
Press the "MODE" button until the"FAN " indica-
tor light comes on.
Press the "FAN SPEED" button on the remote
controller to choose the fan speed. The tempera-
ture can not be adjusted.
Do not put the duct to window.
NOTE: Under AUTO mode, both the AUTO mode
and the actual operation mode indicator lights
illuminate for some models.
HEAT operation(cooling only models
without)
•
•
•
Press the "MODE" button until the "HEAT" indica-
tor light comes on.
Press the ADJUST buttons "+" or " - " to select
your desired room temperature. The temperature
can be set within a range of
17°C~30°C/62°F~88°F (or 86°F).
Press the "FAN SPEED" button on the remote
controller to choose the fan speed.
AUTO operation(on some models)
•
•
•
When you set the air conditioner in AUTO mode,
it will automatically select cooling, heating(cool-
ing only models without), or fan only operation
depending on what temperature you have select-
ed and the room temperature.
The air conditioner will control room temperature
automatically round the temperature point set by
you.
Under AUTO mode, you can not select the fan
speed.
Operating Instructions
NOTE:This feature can be activated from the remote
control ONLY. The remote control serves as a remote
end of the hose directly over the drain area in your base-
ment floor.
/2°F (or 1°F) after an additional 30 minutes. This new
temperature will be maintained for 7 hours before it
thermostat allowing for the precise temperature
control at its location. To activate the Follow Me/Temp
Sensing feature, point the remote control towards the
unit and press the Follow Me/Temp Sensing button.
The remote control will send this signal to the air
conditioner until press the Follow Me/Temp Sensing
button again. If the unit does not receive the Follow
Me/Temp Sensing signal during any 7 minutes interval,
the unit will exit the Follow Me/Temp Sensing mode.
To Next Page
Loading...
