EasyManuals Logo
Home>Midea>Dehumidifier>MDDG-20DEN7-QA3

Midea MDDG-20DEN7-QA3 User Manual

Midea MDDG-20DEN7-QA3
11 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
OPERATING THE UNIT
When using the unit
When first using the dehumidifier, operate the unit
continuously 24 hours.
A dehumidifier operating in a basement will have little or no effect in drying an adjacent enclosed
storage area, such as a closet, unless there is adequate circulation of air in and out of the area.
Air outlet grille
Air intake
grille
20cm or more
20cm or more
20cm or more
20cm or more
40cm or
more
Positioning the unit
Do not use outdoors.
This dehumidifer is intended for indoor residential
applications only. This dehumidifier should not be used
for commercial or industrial applications.
Place the dehumidifier on a smooth, level floor strong
enough to support the unit with a full bucket of water.
Allow at least 20cm of air space on all sides of the unit
for good air circulation.
Place the unit in an area where the temperature will not
O O
fall below 5 C(41 F). The coils can become covered with
O O
frost at temperatures below 5 C(41 F), which may reduce
performance.
Place the unit away from the clothes dryer, heater or radiator.
Use the unit to prevent moisture damage anywhere books
or valuables are stored.
Use the dehumidifier in a basement to help prevent
moisture damage.
The dehumidifier must be operated in an enclosed
area to be most effective.
Close all doors, windows and other outside openings
to the room.
Fig.4
Casters(Install at four points on the
bottom of unit)
Do not force casters to move over
carpet, nor move the unit with water
in the bucket. (The unit may tip over
and spill water.)
NOTE:Casters is optional,some
models without.
Removing the collected water
1. Pull out the bucket a little.
2. Hold both sides of the bucket
with even strength, and pull it
out from the unit.
3. Pour the water out.
NOTES:
When you remove the bucket, do not touch any parts
inside of the unit. Doing so may damage the product.
Be sure to push the bucket gently all the way into the
unit. Banging the bucket against anything or failing to
push it in securely may cause the unit not to operate.
When you remove the bucket,if there is some water in
the unit you must dry it .
Fig.5
Fig.6
OPERATING THE UNIT
2. Continuous draining
Fig.7
NOTE: When the continuous drain feature is not being
used, remove the drain hose from the outlet and reinstall
the rubber plug.
Attach the hose
to the drain
hose outlet.
Remove the
rubber plug
Water can be automatically emptied into a floor
drain by attaching the unit with a water hose
(not included).
Remove the rubber plug from the back drain
hose outlet. Attach a drain hose(ID=13.5mm)
and lead it to the floor drain or a suitable
drainage facility(see Fig.7).
Make sure the hose is secure so there are no leaks.
Direct the hose toward the drain,making sure that
there are no kinks that will stop the warter flowing.
Place the end of the hose into the drain and make sure
the end of the hose is level or down to let the water flow
smoothly. Donever let it up.
Make sure the water hose is lower than the drain hose
outlet.
Select the desired humidity setting and fan speed
on the unit for continuous draining to start.
This unit is designed to operate with a working
O O O O
environment between 5 C/41 F and 32 C/90 F, and
between 30%(RH) and 80%(RH).
If the unit has been switched off and needs to be
switched on again quickly, allow approximately
three minutes for the correct operation to resume.
Do not connect the dehumidifier to a multiple socket
outlet, which is also being used for other electrical
appliances.
Select a suitable location, making sure you have easy
access to an electrical outlet.
Plug the unit into a electrical socket-outlet with earth
connection.
Make sure the Water bucket is correctly fitted otherwise
the unit will not operate properly.
NOTE:When the water in the bucket reaches to a certain
level,please be careful to move the machine to avoid it
falling down.
14
15
There are two ways to remove collected water.
1. Use the bucket
When the bucket is full, the Full indicator light
will illuminate, the digital display shows P2.
Slowly pull out the bucket. Grip the left and right
handles securely, and carefully pull out straight so
water does not spill. Do not put the bucket on the floor
because the bottom of the bucket is uneven. Otherwise
the bucket will fall and cause the water to spill.
Throw away the water and replace the bucket. The
bucket must be in place and securely seated for the
dehumidifier to operate.
The machine will restore to its original state when the
bucket is replaced in its correct position.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Midea MDDG-20DEN7-QA3 and is the answer not in the manual?

Midea MDDG-20DEN7-QA3 Specifications

General IconGeneral
BrandMidea
ModelMDDG-20DEN7-QA3
CategoryDehumidifier
LanguageEnglish

Related product manuals