Page 12
Operating
Instructions
Wireless button(On some models)
If connection (router) is successful within 8 minutes,
the unit will exit Wireless connection mode automatically
and the Wireless indicator illuminates and the unit
enters the previous function. If connection is failure
within 8 minutes, the unit exits the Wireless connection
mode automatically.
Fan button
Control the fan speed.Press to select fan speed
in three steps-low, med and high.(On some models
The fan speed just can be selected in two steps-low
and high.)The fan speed indicator light illuminates
under different fan speed settings.
Press and hold the Fan button for 3 seconds to
eliminate filter reminder, when the filter light flickers
(On some models)
.
UP( )/DOWN( ) buttons
· Humidity Set Control buttons
In Setting dehumidifying mode, The humidity level can be
set within a range of 35%RH(Relative Humidity) to 85%RH
(Relative Humidity) in 5% increments. Press and hold the
button the humidity drop continuously.Press and
hold the button the humidity rise continuously.
FILL LEVEL button
Control the bucket capacity.Press to select bucket
capacity in four steps-1, 2, 3 and 4. When turn on
pump function, the pump indicator light illuminates
and the bucket capacity will be at 4 step.
· Press to initiate the Auto start or Auto stop feature,
in conjuction with the and buttons. When the
unit is on, press the Timer button to activate the Auto
stop feature. When the unit is off, press this button
to activate the Auto start feature.
· Press or hold the and button to change the
Auto time by 0.5 hour increments, up to 10 hours,
then at 1 hour increments up to 24 hours.
· The control will count down the time remaining until
start.
· The selected time will register in 5 seconds and the
system will automatically revert back to display the
previous humidity setting.
· Turning the unit ON or OFF at any time or adjusting
the timer setting to 0.0 will cancel the Auto start or
Auto stop feature.
· When LED display window displays the code of P2,
the Auto start or Auto stop feature will also be
cancelled.
Timer button
· PUMP feature(On some models)
Press and hold on the Up/Down buttons 2 second to
initiate PUMP feature
.
Press and hold on the Up/Down
buttons 2 seconds again to stop PUMP feature.
Turn on the PUMP feature, the bucket capacity cannot
be selected and the bucket capacity is at 4 step.
· FRESH feature(On some models)
Press and hold on the Up/Down buttons 2 seconds to
initiate FRESH feature, and
the fresh indicator light
illuminates.
The ion generatoris energized and will help
to purify the air inside.
Press and hold on the Up/Down
buttons 2 seconds again to stop FRESH feature, and
the fresh indicator light
turns dark.
Display
Shows the set % humidity level from 35% to 85% or
auto start/stop time (0~24) while setting, then shows
the actual(±5% accuracy) room % humidity level in a
range of 30% RH(Relative Humidity) to 90%RH(Relative
Humidity).
Error Codes:
EH60-Room temperature r sensor error--Unplug the unit
and plug it back in. If error repeats, call for service;
EH61-Tube Temperature sensor of the evaporator error--
Unplug the unit and plug it back in. If error repeats,
call for service;
EH0b-Display board and master control board
communication error.Unplug the unit and plug it
back in. If error repeats, call for service;
Press and hold on the POWER button for 3 seconds to
initiate the Wireless connection mode. The LED DISPLAY
shows’AP’ to indicate you can set Wireless connection.
Note: The unit operates for 250 hours, then enter
filter clean reminder.
Note: When the PUMP feature is actived, it works
when the water is full at 4 step.
To Next Page
Loading...
Need help?
General
