Miller XT30C - Default Chapter; Table of Contents

TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1.................................
1-1. Symbol Usage 1.......................................................................
1-2. Plasma Arc Cutting Hazards 1...........................................................
1-3. Additional Symbols For Installation, Operation, And Maintenance 3.............................
1-4. California Proposition 65 Warnings 4......................................................
1-5. Principal Safety Standards 4.............................................................
1-6. EMF Information 4.....................................................................
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION 5..........................
2-1. Signification des symboles 5.............................................................
2-2. Dangers liés au coupage à l’arc au plasma 5...............................................
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance 7.....
2-4. Proposition californienne 65 Avertissements 9..............................................
2-5. Principales normes de sécurité 9.........................................................
2-6. Informations relatives aux CEM 9.........................................................
SECTION 3 − SPECIFICATIONS 10..............................................................
3-1. XT30 Specifications 10..................................................................
3-2. XT30 Torch Dimensions 10...............................................................
3-3. XT30C Specifications 11.................................................................
3-4. XT30C Torch Dimensions 11..............................................................
3-5. XT40 Torch Specifications 12.............................................................
3-6. XT40 Torch Dimensions 12...............................................................
3-7. XT60 Torch Specifications 13.............................................................
3-8. XT60 Torch Dimensions 13...............................................................
SECTION 4 − INSTALLATION 14................................................................
4-1. Installing 30 Ampere (XT30) Torch And Work Cable On Spectrum 375 X-TREME
(Stock No. 907 529), And Using Trigger Safety Lock 14.......................................
4-2. Installing 30 Ampere (XT30) Torch And Work Cable On Spectrum 375 X-TREME
(Stock No. 907 303 And 907 339) Prior To Serial No. MB290336P, And Using
Trigger Safety Lock 15...................................................................
4-3. Installing 30 Ampere (XT30C) Torch And Work Cable On Spectrum 375
(Stock No. 907532), And Using Trigger Safety Lock 16........................................
4-4. Installing 30 Ampere (XT30C) Torch And Work Cable On Spectrum 375
(Stock No. 903 891), And Using Trigger Safety Lock 17.......................................
4-5. Installing 40 Ampere (XT40) Torch And Work Cable On Spectrum 625 X-TREME
(Stock No. 907 404 And 907 531), And Using Trigger Safety Lock 18............................
4-6. Connecting And Disconnecting 40 Ampere (XT40) Torch On Spectrum 625 X-TREME
(Stock No. 907 579), And Using Trigger Safety Lock 19.......................................
4-7. Connecting And Disconnecting Work Cable On Spectrum 625 X-TREME
(Stock No. 907 579) 19..................................................................
4-8. Connecting And Disconnecting 60 Ampere (XT60) Torch On Spectrum 875
And Spectrum 875 Auto-Line, And Using Trigger Safety Lock 20................................
SECTION 5 − OPERATION 21...................................................................
5-1. Plasma Cutting System Practices 21.......................................................
5-2. Sequence Of Cutting Operation 22.........................................................
5-3. Sequence Of Piercing Operation 23........................................................
SECTION 6 − MAINTENANCE & TROUBLESHOOTING 24.........................................
6-1. Routine Maintenance 24.................................................................
6-2. Shield Cup Shutdown System 24..........................................................
6-3. Checking/Replacing Retaining Cup, Tip, And Electrode 25.....................................
6-4. Troubleshooting 26......................................................................
SECTION 7 − PARTS LIST 27...................................................................
WARRANTY