How to fix a Millipore Water Filtration UV System only?
If you're experiencing issues with only the UV System of your Millipore Water Filtration System: * The UV Timer might be exhausted, indicating the need to replace the UV Lamp. * The UV Lamp might not be installed correctly or not installed at all. Power OFF the system and reinstall the UV Lamp.
Why is there low or no water flow when dispensing from my Millipore Water Filtration System?
Low or no water flow when dispensing from your Millipore Water Filtration System can occur for several reasons: * The water level might be less than 10%, preventing dispensing. Allow the system to enter FILLING TANK mode until the Tank Level display shows sufficient water. * The Tank Outlet Valve could be open, preventing the tank from filling. Ensure the Tank Outlet Valve is closed. * The Millipak Filter might be air locked. Vent all air from the Millipak Filter. * The Final Filter might be clogged.
What should I do if the last Product resistivity value is not displayed on my Millipore Water Filtration System?
If the last Product resistivity value isn't showing on your Millipore Water Filtration System, there could be several reasons: * A measurement might not have been taken during DISPENSING mode or recirculation. Manually dispense or recirculate water to initiate a Product resistivity reading. * The Tank Outlet Valve might not be open. Open the Tank Outlet Valve to drain the water from the tank. * The SmartPak cartridge lifetime may be exhausted. Replace the SmartPak cartridge. * The SmartPak cartridge might not be installed correctly or not installed at all. Reinstall the SmartPak cartridge. * The system may have been in STANDBY mode for a while. Recirculate the water in the system.
Why is the Tank Level display not rising in FILLING TANK mode on my Millipore Water Filtration System?
If the Tank Level display isn't rising during FILLING TANK mode on your Millipore Water Filtration System, consider the following: * The Tank Outlet Valve might be open, diverting water to the drain. Close the Tank Outlet Valve. * The RO membrane could be dirty or clogged. Replace the SmartPak cartridge.
Why is the AUTO-DISPENSING mode not accurate on my Millipore Water Filtration System?
Inaccurate AUTO-DISPENSING mode on your Millipore Water Filtration System can be due to: * The Product Water flowrate not being calibrated. * The Final Filter being clogged or airlocked. Replace the Final Filter.
What causes the DISPENSING mode to run continuously on my Millipore Water Filtration System?
If the DISPENSING mode runs continuously on your Millipore Water Filtration System, even when the Tank Level display is below 10%, the water level may not be calibrated.
What to do if the RO Permeate conductivity value is not displayed on my Millipore Water Filtration System?
To display the RO Permeate conductivity value on your Millipore Water Filtration System, ensure that the measurement was made while dispensing water during FILLING TANK mode. If not, dispense water during FILLING TANK mode to start a RO Permeate conductivity reading again.
What to do if the display screen is blank on my Millipore Water Filtration System?
If the display screen on your Millipore Water Filtration System is blank, here are a few things to check: * Make sure the power cord is properly plugged in. * Verify that there is a source of electrical power. * If the above steps don't resolve the issue, the Main Power Fuse may be blown.
Instructions on safe operation, emphasizing adherence to hydraulic and electrical specifications.
Details on water flowrate specifications and product water quality parameters like resistivity and TOC.
Provides dimensions, weight, noise level, and electrical specifications for the Direct-Q R systems.
Lists feedwater requirements, connection needs, reject flow, and environmental requirements for system installation.
Step-by-step guide for installing the SmartPak cartridge, including precautions.
Detailed procedure for calibrating the tank level sensor for specific models.
Step-by-step guide to calibrate the product water flowrate using a graduated cylinder.
Procedure to set the resistivity setpoint for low resistivity alerts.
Procedure for dispensing a specific, pre-set volume of product water.
Explanation of system messages and alarms like Pack Alarm and UV Lamp Alarm.
Step-by-step guide for removing and installing a new SmartPak cartridge.
Detailed steps for removing the old final filter and installing a new one.
Instructions for calibrating the tank level sensor.
Comprehensive guide for sanitizing the entire water system to eliminate bacteria.
Procedure specifically for sanitizing only the water tank.
Step-by-step instructions for replacing the UV lamp.
Solutions for issues with low or no water flow during dispensing.
Troubleshooting for an exhausted UV timer and related alarms.
General| Model | Direct-Q 5 UV-R |
|---|---|
| Resistivity | 18.2 MΩ·cm at 25°C |
| TOC | < 5 ppb |
| Bacteria | < 1 CFU/mL |
| Pyrogens (Endotoxins) | < 0.001 EU/mL |
| Type | Water Purification System |
| Technology | Reverse Osmosis, UV Lamp, Ion Exchange |
| Water Quality | Type I ultrapure water |
| Feed Water Requirements | Potable water |
| Power Supply | 220-240 V, 50/60 Hz |
To Next Page