Milnor 42026 - Mechanical Parts And Service Manual

116 pages

Save Page as PDF

To Next Page

PELLERIN MILNOR CORPORATION Post Office Box 400, Kenner, Louisiana 70063–0400, U.S.A.

Mechanical Parts and

Service

36021 & 36026V5J,

V5Z, V7Z; 42026V5J;

42026 & 42030V6Z

Manual Number: MCWOBM01

Edition (ECN): 2023346A

Main Page

Table of Contents3
36021V5J, V5Z, V7Z; 36026V5J, V5Z, V7Z; 42026V5J, V6Z6
General Service & Safety-Related Components7
Limited Standard Warranty8
How to Get the Necessary Repair Components9
Trademarks9
Safety - Rigid Washer Extractors10
Safety Alert Messages-Internal Electrical and Mechanical Hazards10
Safety Alert Messages-Cylinder and Processing Hazards10
Table 1 Trademarks10
Safety Alert Messages-Unsafe Conditions12
Damage and Malfunction Hazards12
Hazards Resulting from Inoperative Safety Devices12
Hazards Resulting from Damaged Mechanical Devices12
Careless Use Hazards13
Careless Operation Hazards-Vital Information for Operator Personnel (See also Operator Hazards Throughout Manual)13
Careless Servicing Hazards-Vital Information for Service Personnel (See also Service Hazards Throughout Manuals)13
Safety Placard Use and Placement 36021CPE, NSP, V5J, V5Z and 36026V5J, V5Z16
36021CPE, NSP, V5J, V5Z and 36026V5J, V5Z18
36021V7J, V7Z; 36026V7J/W, V7Z; 42026V5J; 42026V6J/W, V7Z; 42030V6J, V6Z20
Safety Placard Use and Placement-ISO22
36021V7J, V7Z; 36026V7J/W, V7Z; 42026V5J; 42026V6J/W, V6Z; 42030V6J, V6Z22
Guards & Covers 36021V5Z, 36026V5Z24
Guards & Covers 36021V7Z, 36026V7Z, 42026V5J, 42026V6Z, 42030V6Z26
Figure 1 Front Covers26
Figure 2 Rear Covers and Side Gasket27
Torque Requirements for Fasteners28
Torque Values28
Fasteners Made of Carbon Steel28
Without a Threadlocker28
Figure28
Table 8 Torque Values for Standard Fasteners with Maximum 5/16-Inch Diameters and no Lubricant28
Table 9 Torque Values for Standard Fasteners Larger than 5/16-Inch Diameters and no Lubricant29
Table 10 Torque Values for Plated Fasteners with Maximum 5/16-Inch Diameters and no Lubricant29
With a Threadlocker30
Table 11 Torque Values for Plated Fasteners Larger than 5/16-Inch Diameters and no Lubricant30
Stainless Steel Fasteners32
Preparation33
How to Apply a Threadlocker34
Blind Holes34
Through Holes34
Figure 4 Apply Threadlocker in a Blind Hole34
Figure 5 Apply Threadlocker in a through Hole35
Drive Assemblies36
Drive Chart 36021V5J, 36021V5Z, 36026V5J, 36021V5Z38
Drive Chart 36021V7J, 36021V7Z, 36026V7J, 36026V7Z40
Drive Chart 42026V5J, 42026V6J, 42026V6Z, 42030V6J, 42030V6Z42
Drive Pulley and Belt Maintenance44
Pulley Requirements44
Condition of Grooves on Pulleys44
Pulley and Shaft Position45
Keep Run-Out in Tolerance46
Belt Requirements47
Condition of Belts47
Tension of Belts48
The Pulleys Must Stay Aligned When You Adjust the Belt Tension49
How to Do Maintenance on Pulleys and Belts50
Typical Steps to Replace Pulleys and Belts50
Run-Out50
Examples of Procedures Used at the Milnor Factory to Align51
Pulleys51
Motor Mount 30015, 30022, 36021, 36026, 42026, & 42030Vxx,Txx53
Bearing Assembly 36021V5J, 36021V5Z, 36026V5J, 36026V5Z with Starplate56
Bearing Assembly 36021V7Z, 36026V7Z, 42026V5J, 42026V6Z, 42030V6Z59
Cylinder & Shell63
Main Bearing, Shell, Cylinder Installation64
36021V5J, 36021V5Z, 36026V5J, 36026V5Z with Starplate64
36021V7Z, 36026V7Z, 42026V5J, 42026V6Z, 42030V6Z69
Cross Section of Shell, Cylinder, Bearing, and Frame69
Main Bearing, Shell, and Cylinder Installation70
20 Inch Door Assemblies after 8/201673
42030V6Z74
Mcr12; Mct16/18/27; Mwf18/27; Mwr27/36; Mwt12/16/18/27; 3015/3022T6X, Vrj, V8Z, Vzz; 3022X8R; 36021V5J, V5Z, V7Z; 36026V5J, V5Z, V7Z78
42026V5J, V6Z. 42030V6Z78
Door Lock Mechanisms79
Door Handle and Lock Actuator81
Door Handle and Lock Actuator82
Chemical Supply Devices84
42030V6Z88
Soap Chute 36021V5J, V5Z, V7Z; 36026V5J, V5Z, V7Z; 42026V5J, V6Z; 42030V6Z88
42030V6Z90
Supply Chute90
Valve Manifold91
Water & Steam94
Water Schematic 36021V5J, V5Z, V7Z; 36026V5J, V5Z, V7Z; 42026V5J, V6Z; 42030V6Z96
42030V6Z98
Steam Inlet 36021V5J, V5Z, V7Z; 36026V5J, V5Z, V7Z; 42026V5J, V6Z; 42030V6Z104
Drain Valve 36021V5J, V5Z, V7Z; 36026V5J, V5Z, V7Z; 42026V5J, V6Z; 42030V6Z106
Inch Electrical Drain Valve108
Control & Sensing110
42030V6Z111
36021V5J, V5Z, V7Z; 36026V5J, V5Z, V7Z; 42026V5J, V6Z; 42030V6Z112
Vibration Safety Switch Adjustments114
What the Vibration Safety Switch Does114
Adjustments114
Vibration Safety Switch116

Milnor 42026 - Mechanical Parts And Service Manual

Table of Contents

Other manuals for Milnor 42026

Related product manuals