BeneVision N Series Patient Monitor Operator’s Manual 11
21.7.2 Changing Patient Information ................................................................................................................................................21 - 4
21.7.3 Changing the ICG Wave Sweep Speed ................................................................................................................................21 - 5
21.7.4 Selecting ICG Parameters ..........................................................................................................................................................21 - 5
21.8 ICG Troubleshooting .................................................................................................................................................................................21 - 5
22 Monitoring Continuous Cardiac Output (from PiCCO Module) .................................................................................22 - 1
22.1 CCO Introduction .......................................................................................................................................................................................22 - 1
22.2 CCO Safety Information ...........................................................................................................................................................................22 - 1
22.3 Zeroing the IBP transducer .....................................................................................................................................................................22 - 2
22.4 PiCCO Display ..............................................................................................................................................................................................22 - 2
22.4.1 CCO Display ...................................................................................................................................................................................22 - 2
22.4.2 pArt Display ...................................................................................................................................................................................22 - 3
22.4.3 pCVP Display ..................................................................................................................................................................................22 - 3
22.5 Accessing the On-screen CCO Guide ..................................................................................................................................................22 - 3
22.6 CCO Equipment to Patient Connection .............................................................................................................................................22 - 4
22.6.1 Preparing to Monitor C.O. .........................................................................................................................................................22 - 4
22.6.2 Performing the CCO Settings ..................................................................................................................................................22 - 5
22.6.3 Performing C.O. Measurement ...............................................................................................................................................22 - 6
22.7 Accessing the HemoSight Menu ..........................................................................................................................................................22 - 7
22.8 Changing CCO Settings ...........................................................................................................................................................................22 - 7
22.8.1 Changing CCO and CCI Alarm Settings ...............................................................................................................................22 - 7
22.8.2 Setting Parameters for Display ...............................................................................................................................................22 - 7
22.9 PiCCO Troubleshooting ...........................................................................................................................................................................22 - 8
23 Monitoring Carbon Dioxide (CO
2
) ................................................................................................................................23 - 1
23.1 CO
2
Introduction ........................................................................................................................................................................................23 - 1
23.2 CO
2
Safety Information ............................................................................................................................................................................23 - 2
23.3 CO
2
Measurement Limitations ..............................................................................................................................................................23 - 2
23.4 CO
2
Display ..................................................................................................................................................................................................23 - 2
23.5 Measuring CO
2
Using Sidestream/Microstream CO
2
Module ...................................................................................................23 - 3
23.5.1 Preparing to Measure CO
2
Using Sidestream CO
2
Module ..........................................................................................23 - 3
23.5.2 Preparing to Measure CO
2
Using Microstream CO
2
Module .......................................................................................23 - 5
23.5.3 Zeroing the Sidestream/Microstream CO
2
Module ........................................................................................................23 - 5
23.6 Measuring CO
2
Using Mainstream CO
2
Module ............................................................................................................................. 23 - 6
23.6.1 Preparing to Measure CO
2
Using Mainstream CO
2
Module .........................................................................................23 - 6
23.6.2 Zeroing the Mainstream CO
2
sensor ....................................................................................................................................23 - 7
23.7 Changing Settings for All CO
2
Modules .............................................................................................................................................23 - 7
23.7.1 Changing CO
2
Alarm Settings .................................................................................................................................................23 - 7
23.7.2 Setting the CO
2
Waveform .......................................................................................................................................................23 - 7
23.7.3 Setting the RR Source .................................................................................................................................................................23 - 7
23.7.4 Entering the Standby Mode .....................................................................................................................................................23 - 8
23.7.5 Entering the Intubation Mode ................................................................................................................................................23 - 8
23.8 Changing Settings for Sidestream and Microstream CO
2
Module ..........................................................................................23 - 8
23.8.1 Setting the Auto Standby .........................................................................................................................................................23 - 8
23.8.2 Setting Humidity Compensation ...........................................................................................................................................23 - 8
23.9 Changing O
2
Settings (For Sidestream CO
2
Module Integrating O
2
) .....................................................................................23 - 9
23.9.1 Changing O
2
Alarm Settings ....................................................................................................................................................23 - 9