Mindray BeneVision N22 Quick Reference Guide

Mindray BeneVision N22

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

BeneVision N22/N19/N17/N15/

N12

Quick Reference Guide

Table of Contents

Default Chapter3
- Table of Contents3
Quick Keys7
Gestures10
Patient Setup10
- Admit Patient and Enter Demographics (Manual Entry)10
- Enter Demographics from the ADT Database11
- Discharge a Patient12
Standby12
- Enter Standby12
- Resume Monitoring13
- Realtime Waveforms13
- Adjust Recorder's Waveforms13
Print13
- Realtime Waveforms (Laser Printer Connection Required)13
- Adjust Printed Waveforms14
- End Case Report14
Ecg15
- Adjust ECG Lead15
- Enable Pacemaker Detection15
- Initiate ECG Relearn15
- Initiate ST Analysis15
Nibp17
- Initiate a Non-Invasive Blood Pressure Measurement (NIBP)17
- Stop Non-Invasive Blood Pressure Measurement (NIBP)17
- Set a Non-Invasive Blood Pressure Measurement Interval18
- Configure a Custom Sequence18
- Factors that Affect Blood Pressure Measurement Accuracy18
Invasive Blood Pressures (Optional)20
- Adjust Invasive Blood Pressure Label20
- Zero Invasive Blood Pressure21
Continuous Cardiac Output (Optional)21
- Adjust the Displayed Parameters21
Central Venous Oxygen Saturation (Optional)22
- Print Oxygenation Parameters22
Bispectral Index (Optional)22
- Adjust bis Waveform Area22
- BIS Expand View (Bilateral Sensor Required)23
- Adjust Parameters23
Alarms23
- Setting Parameter Alarm Properties23
- Changing Arrhythmia Alarm Settings(Arrhythmia Option Required)24
- Disable Non-Lethal Arrhythmia Alarms (Arrhythmia Option Required)25
- Accessing Help When Technical Alarms Occur25
Reset Alarms25
Pause Alarms/Pause Alarm Tones25
Hemodynamic Monitoring26
- Initiate a Cardiac Output Measurement26
- Initiate Pulmonary Artery Wedge Pressure (PAWP)27
- Initiate Hemodynamic Calculations28
Screen Display28
Review30
- Tabular Trends30
- Arrhythmia and Alarm Events31
- Full Disclosure31
- Oxycrg32
Viewing Other Beds32
- Entering the Remote View Screen32
- Adding a Bed32
- Resetting Alarms for Remote Devices33
- Removing a Bed33
- Saving a Manual Event33
- Displaying the Alarm Watch Tile on the Main Screen33
Volumes34
- Alarm Volume34
- Key Volume34
- Beat Tone34
Date and Time35
Parameter Colors36
Load Default (Preset) Settings36
Lock/Unlock Touchscreen Display36
Pair the Tm80 Telemetry Monitor37
- Pair the TM8037
- Unpair the TM80 Telemetry Monitor from the N Series Bedside Monitor37
- Unpair the N Series Bedside Monitor from the TM80 Telemetry Monitor38
Pair Bp10 Nibp Module38
- Pair the BP10 Module with the N Series Bedside Monitor38
- Unpair BP10 Module from the N Series Bedside Monitor39
Cleaning/Disinfecting39
- Cleaning the Main Unit/Module/Smr39
- Disinfecting the Main Unit/Module/Smr40
- Cleaning and Disinfecting the Accessories40
Sterilization40

Other manuals for Mindray BeneVision N22

Operator's Manual472 pages

Service Manual105 pages

Questions and Answers:

S
Susan CostaAug 22, 2025
Why is my Mindray Monitor TM80 prone to offline occasionally?
- B
  brandijimenezAug 22, 2025
  The TM80 may be prone to going offline occasionally on your Mindray monitor due to wireless signal interference or weak signals. Try placing the TM80 in the MPAN or Wi-Fi coverage area, checking for and reducing any interference sources. Weak signals can also cause this issue, so ensure the TM80 is in an area with strong signal strength and remove any metallic obstructions between the TM80 and the monitor. If the issue persists, it may be due to insufficient network bandwidth or greater network delay, in which case you should contact your service personnel.
A
Andrew JohnstonAug 25, 2025
What to do if my Mindray BeneVision N22 says 'Telemetry NIBP Disconnected'?
- G
  Gilbert YorkAug 25, 2025
  If your Mindray monitor displays 'Telemetry NIBP Disconnected', the BP10 might be out of the MPAN coverage area, so put the BP10 in the MPAN coverage area. Alternatively, the BP10 may have been powered off, so power it on. Also, a satellite module rack might not be connected to the monitor properly, so replug the satellite module rack.
S
sotosaraAug 27, 2025
What to do if my Mindray Monitor BP10 is prone to offline occasionally?
- R
  rebecca76Aug 27, 2025
  If the BP10 is prone to going offline occasionally on your Mindray monitor, it might be due to MPAN signal interference. Try placing the BP10 in the MPAN coverage area and check for any interference sources. Weak MPAN signals could also be the cause; ensure the BP10 is in an area with strong signal strength and remove any metallic obstructions between the BP10 and the monitor.
D
Danielle NorrisAug 28, 2025
What to do if my Mindray Monitor displays 'Device Not Found'?
- A
  Amber FisherAug 28, 2025
  If your Mindray Monitor displays 'Device Not Found', it could be due to a few reasons. First, check that the satellite module rack is properly connected to the monitor by replugging it. Also, verify that the monitor is connected to the Wi-Fi network and that its wireless network settings are correct. Finally, confirm that the wireless network supports multicast data transfer, as this is required for the monitor and TM80 to communicate.
R
rebeccaruizAug 29, 2025
How to fix abnormal ECG waves and Pleth waveform on my Mindray BeneVision N22?
- R
  Richard MartinezAug 29, 2025
  If you're seeing abnormal ECG waves and Pleth waveforms from the TM80 on your Mindray monitor after pairing, it could be due to wireless signal interference or weak wireless signals. Try placing the TM80 in the MPAN or Wi-Fi coverage area and check for any interference sources. If the signals are weak, move the TM80 to an area with strong signal strength and remove any metallic obstructions between it and the monitor. If the problem persists, there might be insufficient network bandwidth or a network delay, and you should contact your service personnel.
G
gomezcandiceAug 31, 2025
What to do if Mindray BeneVision N22 Monitor TM80 won't automatically switch to Wi-Fi?
- J
  Jared MarshallAug 31, 2025
  If the TM80 isn't automatically switching to Wi-Fi when out of the MPAN coverage area on your Mindray monitor, verify that the TM80's wireless network settings are correct and that it's connected to the Wi-Fi network. Also, ensure that the monitor is connected to the Wi-Fi network and that its wireless network settings are correct.

Mindray BeneVision N22 Specifications

General

Brand	Mindray
Model	BeneVision N22
Category	Monitor
Language	English

Related product manuals

Mindray BeneVision N19

Preview: Mindray BeneVision TM80

Mindray BeneVision TM80

Preview: Mindray BeneView T8

Mindray BeneView T8

Preview: Mindray VS-900

Preview: Mindray iPM Series

Mindray iPM Series

Preview: Mindray MEC-1000

Mindray MEC-1000

Preview: Mindray VS-800

Preview: Mindray iPM-9800

Mindray iPM-9800

Preview: Mindray VS 8