What to do if Minuteman PRO750RT2U UPS shows error code E01?
If the Minuteman UPS displays error code E01 and shuts down, it indicates a short-circuit on its output. You should check the attached load to resolve this issue.
What to do if Minuteman PRO750RT2U UPS shows error code E02?
If the Minuteman UPS shows the overload icon (Error Code: E02) and a constant alarm, you should check the specifications of the UPS and remove part of the load. If the UPS shuts down because of an overload, the UPS must perform an Inverter function or a Self Test to clear the Overload Alarm.
Why Minuteman PRO750RT2U works in battery mode when AC is present?
If the Minuteman UPS is operating in battery mode even when AC power is present, reset the input circuit breaker by pressing the plunger back in. If the input circuit breaker trips after the UPS restarts, reduce the load on the UPS.
What to do if Minuteman PRO750RT2U shows error code E06?
If the Minuteman UPS displays error code E06 and the Weak/Bad Battery icon is illuminated, you can check the battery connections. Also, you can charge the batteries for 8 hours and retest, or consider replacing the batteries.
Why Minuteman PRO750RT2U UPS shows error code E03?
If the Minuteman UPS displays error code E03, it means the internal or ambient temperature has exceeded the safe operating range. Check the specifications to ensure the UPS is operating within its recommended temperature range.
How to improve Minuteman PRO750RT2U UPS runtime?
If the Minuteman UPS does not provide the expected runtime, charge the batteries for 8 hours and then retest. If the runtime is still less than expected after the charging, the batteries may need to be replaced.
What does error code E07 mean on Minuteman PRO750RT2U UPS?
If the Minuteman UPS shows error code E07, it means the UPS's battery reserve is low. This condition will continue until AC power returns or the UPS shuts down due to battery exhaustion.
What to do if Minuteman PRO750RT2U has AC mode icon but no output?
If the AC mode icon is illuminated on the Minuteman UPS but there is no output, disconnect the computer cable from the UPS and press the On button. If the UPS then works normally, it indicates that the software had control of the UPS.
What does error code E08 mean on Minuteman PRO750RT2U UPS?
If the Minuteman UPS displays error code E08 and the SWF icon is illuminated, have a qualified electrician correct the service wiring.
What to do if Minuteman UPS fault icon is illuminated?
If the Fault icon is illuminated and a constant alarm is sounding on your Minuteman UPS, it indicates an internal problem. Call for service to resolve the issue.
Key safety warnings and precautions for UPS operation.
Warnings regarding proper AC power connection and grounding.
Step-by-step guide to connect UPS internal batteries.
Troubleshooting guide for UPS symptoms and error codes.
Essential safety warnings for handling UPS batteries.
Step-by-step guide for replacing UPS batteries.
General| Capacity | 750VA |
|---|---|
| Input Voltage | 120V |
| Nominal Output Voltage | 120V |
| Output Voltage Regulation | +/- 5% |
| Output Connections | 6 x NEMA 5-15R |
| Input Connection | NEMA 5-15P |
| Form Factor | Rackmount/Tower |
| Rack Height | 2U |
| Battery Recharge Time | 4 hours to 90% |
| Waveform | Sine wave |
| Input Frequency | 50/60 Hz +/- 3 Hz (auto sensing) |
| Data Line Protection | RJ11/RJ45 |
| Battery Type | Sealed Lead Acid |
| Operating Temperature | 32 - 104°F (0 - 40°C) |
| Operating Humidity | 0% to 95% non-condensing |
| Certifications | cUL, UL, FCC Class B |
| Output Power Capacity | 600 Watts |
| Input Voltage Range | 90-140 VAC |
| Product Type | Line-Interactive UPS |
To Next Page