Mitcorp X750 - User Manual

Questions and Answers

A
Autumn BakerAug 13, 2025
What to do if my Mitcorp Analytical Instruments won't power on?
- D
  Donna ParkerAug 13, 2025
  If your Mitcorp Analytical Instruments unit won't power on, there are several potential causes. First, ensure the device isn't out of battery by connecting the power cord to charge it. Next, check that the probe is securely connected by screwing the probe connector on tightly. Also, verify that the environmental temperature isn't too low or too high, placing the system in a normal temperature environment if needed. If these steps don't resolve the issue, the base unit may be broken, and you should contact Mitcorp or your local distributor for repair.
A
Amy DuncanAug 16, 2025
Why is my Mitcorp Analytical Instruments image freezing or showing no image after powering on?
- C
  Cristina KellyAug 16, 2025
  If your Mitcorp Analytical Instruments unit displays no image or the image freezes after powering on, it could be due to several reasons. Try resetting the system first, as the issue might stem from an abnormal power-on. Also, ensure the probe is properly connected by screwing the connector on tightly. If you performed a hot-swap, power on the console after connecting the probe. If the problem persists, the console or probe might be broken, and you should contact Mitcorp or your local distributor for repair.
G
gmccarthyAug 20, 2025
What to do if my Mitcorp Analytical Instruments cannot record?
- S
  Stephanie McfarlandAug 20, 2025
  If your Mitcorp Analytical Instruments unit cannot record, the most likely cause is that there is no SD card inserted. Please insert an SD card into the device.
A
aaron57Aug 25, 2025
Why is the color tone not correct on my Mitcorp Analytical Instruments?
- C
  clarkdavidAug 25, 2025
  If the color tone on your Mitcorp Analytical Instruments is not correct, it may be due to a white balance error. Check and calibrate the white balance settings.
D
Darren LaneAug 27, 2025
What to do if the Mitcorp Analytical Instruments probe doesn’t articulate fully?
- A
  Alvin GouldAug 28, 2025
  If the probe on your Mitcorp Analytical Instruments unit doesn’t articulate fully, consider these potential causes: * The probe might be rolled up, so spread the probes out. * The probe may have been pulled with too much force; avoid excessive pulling. * The probe head might be obstructed, so ensure there's enough room for articulation. If none of these resolve the issue, the probe head might be broken, and you should send it back to Mitcorp for RMA.
J
Joseph HamiltonSep 1, 2025
How to fix an unclear image on my Mitcorp Analytical Instruments?
- M
  Megan LesterSep 1, 2025
  If the image on your Mitcorp Analytical Instruments unit is unclear, the lens may be dirty. Clean the lens with the provided cleaning kit.
J
John GonzalezSep 5, 2025
What does it mean when the charging set LED is flashing on my Mitcorp Analytical Instruments?
- M
  Madeline MaldonadoSep 5, 2025
  If the charging set LED is flashing on your Mitcorp Analytical Instruments, it indicates poor battery conducting. To resolve this: 1. Withdraw the battery from the charging set. 2. Withdraw the power input from the charging set. 3. Reinstall the power input and battery again.
R
Robin HuangSep 8, 2025
Why is the front LED light off on my Mitcorp Analytical Instruments?
- L
  laura46Sep 8, 2025
  If the front LED light is off on your Mitcorp Analytical Instruments unit, the particle-free feature may be enabled. Turn it off and check again.