Mitsubishi Electric FX3U SERIES - Page 11

9
FX3G/FX3U/FX3UC Series Programmable Controllers
Programming Manual - Basic & Applied Instructions Edition
Table of Contents
20. Positioning Control – FNC150 to FNC159 548
20.1 FNC150 – DSZR / Dog Search Zero Return...................................................................................... 549
20.2 FNC151 – DVIT / Interrupt Positioning............................................................................................... 551
20.3 FNC152 – TBL / Batch Data Positioning Mode.................................................................................. 553
20.4 FNC155 – ABS / Absolute Current Value Read................................................................................. 554
20.5 FNC156 – ZRN / Zero Return ............................................................................................................ 555
20.6 FNC157 – PLSV / Variable Speed Pulse Output ............................................................................... 557
20.7 FNC158 – DRVI / Drive to Increment................................................................................................. 559
20.8 FNC159 – DRVA / Drive to Absolute ................................................................................................. 561
21. Real Time Clock Control – FNC160 to FNC169 563
21.1 FNC160 – TCMP / RTC Data Compare............................................................................................. 564
21.2 FNC161 – TZCP / RTC Data Zone Compare ....................................................................................566
21.3 FNC162 – TADD / RTC Data Addition ............................................................................................... 568
21.4 FNC163 – TSUB / RTC Data Subtraction.......................................................................................... 570
21.5 FNC164 – HTOS / Hour to Second Conversion................................................................................. 572
21.6 FNC165 – STOH / Second to Hour Conversion................................................................................. 574
21.7 FNC166 – TRD / Read RTC data ...................................................................................................... 576
21.8 FNC167 – TWR / Set RTC data......................................................................................................... 577
21.9 FNC169 – HOUR / Hour Meter .......................................................................................................... 579
22. External Device – FNC170 to FNC179 581
22.1 FNC170 – GRY / Decimal to Gray Code Conversion ........................................................................ 582
22.2 FNC171 – GBIN / Gray Code to Decimal Conversion ....................................................................... 583
22.3 FNC176 – RD3A / Read form Dedicated Analog Block ..................................................................... 584
22.4 FNC177 – WR3A / Write to Dedicated Analog Block......................................................................... 585
23. Introduction of Alternate Instructions – FNC180 586
23.1 Instruction correspondence table ....................................................................................................... 586
24. Others – FNC181 to FNC189 587
24.1 FNC182 – COMRD / Read Device Comment Data ........................................................................... 588
24.2 FNC184 – RND / Random Number Generation................................................................................. 590
24.3 FNC186 – DUTY / Timing Pulse Generation ..................................................................................... 591
24.4 FNC188 – CRC / Cyclic Redundancy Check ..................................................................................... 593
24.5 FNC189 – HCMOV / High-Speed Counter Move............................................................................... 597
25. Block Data Operation – FNC190 to FNC199 601
25.1 FNC192 – BK+ / Block Data Addition................................................................................................. 602
25.2 NFC193 – BK– / Block Data Subtraction .......................................................................................... 605
25.3 FNC194~199 – BKCMP=, >, <, < >, <=, >= / Block Data Compare.................................................. 608
26. Character String Control – FNC200 to FNC209 613
26.1 FNC200 – STR / BIN to Character String Conversion ....................................................................... 614
26.2 FNC201 – VAL / Character String to BIN Conversion........................................................................ 619
26.3 FNC202 – $+ / Link Character Strings ............................................................................................... 624
26.4 FNC203 – LEN / Character String Length Detection ......................................................................... 626
26.5 FNC204 – RIGHT / Extracting Character String Data from the Right ................................................ 628
26.6 FNC205 – LEFT / Extracting Character String Data from the Left ..................................................... 630
26.7 FNC206 – MIDR / Random Selection of Character Strings ............................................................... 632