10
FX3G/FX3U/FX3UC Series Programmable Controllers
Programming Manual - Basic & Applied Instructions Edition
Table of Contents
26.8 FNC207 – MIDW / Random Replacement of Character Strings........................................................ 635
26.9 FNC208 – INSTR / Character string search....................................................................................... 638
26.10 FNC209 – $MOV / Character String Transfer .................................................................................. 640
27. Data Operation 3 – FNC210 to FNC219 642
27.1 FNC210 – FDEL / Deleting Data from Tables.................................................................................... 643
27.2 FNC211 – FINS / Inserting Data to Tables ........................................................................................ 645
27.3 FNC212 – POP / Shift Last Data Read [FILO Control] ...................................................................... 647
27.4 FNC213 – SFR / Bit Shift Right with Carry......................................................................................... 650
27.5 FNC214 – SFL / Bit Shift Left with Carry............................................................................................ 652
28. Data Comparison – FNC220 to FNC249 654
28.1 FNC224~230 – LD =, >, <, <>, <=, >= / Data Comparison ................................................................ 656
28.2 FNC232~238 – AND=, >, <, < >, <=, >= / Data Comparison ............................................................. 658
28.3 FNC240~246 – OR=, >, <, < >, <=, >= / Data Comparison ............................................................... 660
29. Data Table Operation – FNC250 to FNC269 662
29.1 FNC256 – LIMIT / Limit Control ......................................................................................................... 663
29.2 FNC257 – BAND / Dead Band Control .............................................................................................. 666
29.3 FNC258 – ZONE / Zone Control........................................................................................................ 669
29.4 FNC259 – SCL / Scaling (Coordinate by Point Data) ........................................................................ 672
29.5 FNC260 – DABIN / Decimal ASCII to BIN Conversion ...................................................................... 676
29.6 FNC261 – BINDA / BIN to Decimal ASCII Conversion ...................................................................... 679
29.7 FNC269 – SCL2 / Scaling 2 (Coordinate by X/Y Data)...................................................................... 682
30. External Device Communication
(Inverter Communication) – FNC270 to FNC275 686
30.1 FNC270 – IVCK / Inverter Status Check............................................................................................ 687
30.2 FNC271 – IVDR / Inverter Drive......................................................................................................... 689
30.3 FNC272 – IVRD / Inverter Parameter Read....................................................................................... 691
30.4 FNC273 – IVWR / Inverter Parameter Write ...................................................................................... 693
30.5 FNC274 – IVBWR / Inverter Parameter Block Write..........................................................................695
30.6 FNC275 – IVMC / Inverter Multi Command ....................................................................................... 697
31. Data Transfer 3 – FNC276 to FNC279 699
31.1 FNC278 – RBFM / Divided BFM Read .............................................................................................. 700
31.1.1 Common items between RBFM (FNC278) instruction and WBFM (FNC279) instruction................... 701
31.2 FNC279 – WBFM / Divided BFM Write.............................................................................................. 704
32. High-Speed Processing 2 – FNC280 to FNC289 706
32.1 FNC280 – HSCT / High-Speed Counter Compare With Data Table.................................................. 707
33. Extension File Register Control – FNC290 to FNC299 712
33.1 FNC290 – LOADR / Load From ER................................................................................................... 713
33.2 FNC291 – SAVER / Save to ER ........................................................................................................ 716
33.3 FNC292 – INITR / Initialize R and ER................................................................................................ 724
33.4 FNC293 – LOGR / Logging R and ER ............................................................................................... 727
33.5 FNC294 – RWER / Rewrite to ER...................................................................................................... 731
33.6 FNC295 – INITER / Initialize ER ........................................................................................................ 737
To Next Page
Loading...
