Mitsubishi Electric Q13UDVCPU - Page 363

361
APPENDICES
A
Appendix 1 Error Codes Appendix 1.5 List of error codes (3000 to 3999)
3013
[PARAMETER ERROR]
Multiple CPU auto refresh setting is any of the
following in a multiple CPU system.
• When a bit device is specified as a refresh
device, a number other than a multiple of 16 is
specified for the refresh-starting device.
• The device specified is other than the one that
may be specified.
• The number of send points is an odd number.
■Collateral information
• Common information: File name/Drive name
• Individual information: Parameter number
■Diagnostic timing
• At power-on/At reset/STOP  RUN/At writing to
programmable controller
Check the following in the refresh setting in
the multiple CPU settings window, and
correct the setting.
• When specifying the bit device, specify a
multiple of 16 for the refresh starting
device.
• Specify the device that may be specified for
the refresh device.
• Set the number of send points to an even
number.
RUN: Off
ERR.:Flashing
CPU Status:Stop
Qn(H)
QnPH
[PARAMETER ERROR]
Multiple CPU auto refresh setting is any of the
following in a multiple CPU system.
• The total number of transmission points is
greater than the maximum number of refresh
points.
■Collateral information
• Common information: File name/Drive name
• Individual information: Parameter number
■Diagnostic timing
• At power-on/At reset/STOP  RUN/At writing to
programmable controller
Check the following in the refresh setting in
the multiple CPU settings window, and
correct the setting.
• The total number of transmission points is
within the maximum number of refresh
points.
Q00/Q01
[PARAMETER ERROR]
Multiple CPU auto refresh setting is any of the
following in a multiple CPU system.
• The device specified is other than the one that
may be specified.
• The number of send points is an odd number.
• The total number of send points is greater than
the maximum number of refresh points.
• The setting of the refresh range crosses over
the boundary between the internal user device
and the extended data register (D) or extended
link register (W).
• No device is set in the host CPU send range.
■Collateral information
• Common information: File name/Drive name
• Individual information: Parameter number
■Diagnostic timing
• At power-on/At reset/STOP  RUN/At writing to
programmable controller
Check the following in the refresh setting in
the multiple CPU settings window, and
correct the setting.
• Specify the device that may be specified for
the refresh device.
• Set the number of send points to an even
number.
• Set the total number of send points within
the range of the maximum number of
refresh points.
• Set the refresh range so that it does not
cross over the boundary between the
internal user device and the extended data
register (D) or extended link register (W).
• For the send range of the host CPU,
refresh target device must be specified. If a
send range is not necessary, delete the
applicable send range.
QnU
3014
[PARAMETER ERROR]
• In a multiple CPU system, the online module
change parameter (multiple CPU system
parameter) settings differ from those of the
ref
erence CPU.
• In a multiple CPU system, the online module
change setting is enabled although the CPU
module mounted does not support online
module change parameter.
• In a multiple CPU system, online module
change parameter was corrected and then it
was written to the CPU module.
■Collateral information
• Common information: File name/Drive name
• Individual information: Parameter number
■Diagnostic timing
• At power-on/At reset/At writing to programmable
controller
• Match the online module change parameter
with that of the reference CPU.
• If the CPU module that does not support
online module change is mounted, replace
it with the CPU module that supports online
module change.
RUN: Off
ERR.:Flashing
CPU Status:Stop
Qn(H)
QnPH
QnU
Error
code
Error and cause Corrective action
LED status,
CPU status
Corresponding
CPU