418
413D
H
File-related
error
The specified file capacity cannot be secured.
Execute again after increasing the capacity of the
specified drive (memory).
QCPU
LCPU
413E
H
File-related
error
Operation is disabled for the specified drive
(memory).
Execute again after changing the target drive
(memory).
QCPU
LCPU
413F
H
File-related
error
The file is inhibited from write to the standard
RAM.
Execute again after changing the specified drive
(memory).
QCPU
LCPU
414A
H
Intelligent
function
module
specification
error
Operation was executed for the intelligent
function module of the non-control group in the
multiple CPU system.
Execute the operation again from the control CPU
of the target module.
QCPU
414C
H
Intelligent
function
module
specification
error
The I/O address of the specified CPU module is
wrong.
Execute again after checking the I/O address of
the specified CPU module.
QCPU
LCPU
4150
H
File-related
error
An attempt was made to format the drive
protected by the system.
Do not format the target drive (memory) as it
cannot be formatted.
QCPU
LCPU
4151
H
File-related
error
An attempt was made to delete the file protected
by the system.
Do not delete the target file as it cannot be deleted.
QCPU
LCPU
4160
H
Online
registration
error
The registered number of forced inputs/outputs
exceeded the maximum value.
Deregister the unused forced inputs/outputs.
QCPU
LCPU
4165
H
Online
registration
error
The multiple-block online change system file
does not exist.
Execute again after securing the area that enables
multiple-block online change at the time of
programmable controller memory format.
QCPU
4166
H
Online
registration
error
Online change (files) is disabled because it is
being executed from the same source.
Due to unsuccessful online change (files)
previously occurred for some reason (example:
communication failure), the processing is kept
incomplete.
Forcibly perform another online change (files).
Qn(H)
QnPH
QnPRH
4167
H
Online
registration
error
Online change (files) is disabled because it is
being performed from another source.
Due to unsuccessful online change (files) from
another source previously occurred for some
reason (example: communication failure), the
processing is kept incomplete.
If online change (files) is not being performed by
any other programming tool, forcibly perform
another online change (files).
Qn(H)
QnPH
QnPRH
4168
H
Online
registration
error
The number of registered executional
conditioned device test settings exceeds 32.
Disable the executional conditioned device test
settings registered in the CPU module, or
decrease the number of test settings registered for
the same step number.
QCPU
LCPU
4169
H
Online
registration
error
No executional conditioned device test settings
are registered.
Check the number of executional conditioned
device test settings registered in the CPU module,
and disable the settings.
QCPU
LCPU
416A
H
Online
registration
error
The specified executing condition does not exist.
(Executional conditioned device test)
Check whether the specified executing conditions
(program, step No. operation timing, device name)
specified when the settings were disabled are
registered.
QCPU
LCPU
416B
H
Online
registration
error
The specified program is SFC program.
(Executional conditioned device test)
Change the program specified when the
executional conditioned device test settings are
registered or disabled.
QCPU
LCPU
4170
H
Ethernet I/F
Error
The password is wrong.
Check the specified remote password, then
execute the lock/unlock processing of the remote
password again.
QCPU
LCPU
4171
H
Ethernet I/F
Error
The port for communication use is at remote
password locking status.
Execute communication after unlocking the remote
password processing.
QCPU
LCPU
Error code
(Hexadecimal)
Error item Error details Corrective action
Corresponding
CPU
To Next Page
Loading...
