Mitsubishi Electric Q13UDVCPU - Page 450

448
C124
H
E-mail related
error
The response from the SMTP server timed out.
(SMTP state transition timeout error)
• Check that the SMTP server is operating
correctly.
• Check that there is no load on the network.
LCPU
C126
H
E-mail related
error
Connection to the SMTP server cannot be
closed. (Failed-to-close-connection error)
• Check that the SMTP server is operating
correctly.
• Check that there is no load on the network.
LCPU
C13D
H
E-mail related
error
SMTP server authentication error
• Check that the account name and password of
the SMTP server are correctly set.
• Check the operating status of the SMTP server.
LCPU
C13E
H
E-mail related
error
SMTP server authentication unsupported error
• Check that the SMTP server supports SMTP
Authentication.
• Change the authentication setting in parameter.
(Deselect the "Authenticate" checkbox, or select
"Use POP before SMTP").
LCPU
C140
H
E-mail related
error
Connection to the POP3 server cannot be
opened. (TCP connection timeout error)
• Check the port number of the POP3 server.
• Check that the communications with the POP3
server is enabled by using the PING command.
LCPU
C141
H
E-mail related
error
The CPU module cannot communicate with the
POP3 server. (Error response) (TCP connection
error)
Check that the POP3 server is not busy. LCPU
C144
H
E-mail related
error
The CPU module was not able to receive a
response from the POP3 server. (POP3 state
transition timeout error)
• Check that the POP3 server is operating
correctly.
• Check that there is no load on the network.
LCPU
C146
H
E-mail related
error
Connection to the POP3 server cannot be
closed. (Failed-to-close-connection error)
• Check that the POP3 server is operating
correctly.
• Check that there is no load on the network.
LCPU
C151
H
E-mail related
error
The e-mail address set to the CPU module in E-
mail Setting parameter differs from the account
name set to the mailbox on the server side.
(User mailbox specification error)
Correct the e-mail address set to the CPU module
so that the account name matches the one set to
the server.
LCPU
C152
H
E-mail related
error
The password set to the CPU module in E-mail
Setting parameter differs from the one set on the
server side. (Password setting error)
Correct the password set to the CPU module so
that it matches the one set to the server.
LCPU
C170
H
E-mail related
error
An error is returned from the DNS server.
• Check that the IP address of the DNS server is
set correctly.
• Check that the mail server name (SMTP server
name, POP server name) is set correctly.
• Check with a network manager if the server set
as a DNS server is operating correctly.
LCPU
C1B6
H
E-mail related
error
The destination number setting is incorrect.
(Destination number setting error)
• Check and correct the destination number
setting.
• Check and correct the e-mail address setting in
parameter or e-mail address table.
LCPU
C400
H
Predefined
protocol related
error (Ethernet)
• SP.ECPRTCL instruction was executed before
the Predefined protocol ready (SM1354) is
turned ON.
• SP.ECPRTCL instruction was executed while
error occurred in the protocol setting data.
• Execute the SP.ECPRTCL instruction after the
Predefined protocol ready (SM1354) is turned
ON.
• Execute the SP.ECPRTCL instruction after
rewriting protocol setting data to CPU.
• If the same error code is displayed again after
rewriting, the cause is a hardware failure of the
CPU module. Please consult your local
Mitsubishi representative.
QnUDV
LCPU
C401
H
Predefined
protocol related
error (Ethernet)
Executed protocol No. has not been registered.
• Execute the protocol again after checking the
specified protocol No.
• Register the corresponding protocol to the
specified protocol No.
QnUDV
LCPU
C402
H
Predefined
protocol related
error (Ethernet)
Protocol setting data is invalid.
Check the protocol setting data and register it
again.
QnUDV
LCPU
C404
H
Predefined
protocol related
error (Ethernet)
SP.ECPRTCL instruction ended abnormally
because the cancel request was accepted during
protocol execution.
Check the canceled protocol in SP.ECPRTCL
instruction control data (number of executions) and
remove the cause of cancel operation.
QnUDV
LCPU
Error code
(Hexadecimal)
Error item Error details Corrective action
Corresponding
CPU