Mitsubishi PUZ-A18NHA6 - Page 103

103
Setting and display items Setting details
Vane · Louver · Vent. (Lossnay) Use to set the vane angle.
•Selectadesiredvanesettingfromvedifferentsettings.
Use to turn ON/OFF the louver.
•Selectadesiredsettingfrom"ON"and"OFF."
Use to set the amount of ventilation.
•Selectadesiredsettingfrom"Off,""Low,"and"High."
High power Use to reach the comfortable room temperature quickly.
•UnitscanbeoperatedintheHigh-powermodeforupto30minutes.
Timer ON/OFF timer* Use to set the operation ON/OFF times.
•Timecanbesetin5-minuteincrements.
Auto-Off timer Use to set the Auto-Off time.
•Timecanbesettoavaluefrom30to240in10-minuteincrements.
Weekly timer* Use to set the weekly operation ON/OFF times.
•Upto8operationpatternscanbesetforeachday.
(NotvalidwhentheON/OFFtimerisenabled.)
Restriction Temp. range Use to restrict the preset temperature range.
•Differenttemperaturerangescanbesetfordifferentoperationmodes.
Operation lock Use to lock selected functions.
•Thelockedfunctionscannotbeoperated.
Energy saving Auto return Use to get the units to operate at the preset temperature after performing energy-save operation for a
specied time period.
•Timecanbesettoavaluefrom30and120in10-minuteincrements.
(Thisfunctionwillnotbevalidwhenthepresettemperaturerangesarerestricted.)
Schedule* Set the start/stop times to operate the units in the energy-save mode for each day of the week, and set the
energy-saving rate.
•Upto4energy-saveoperationpatternscanbesetforeachday.
•Timecanbesetin5-minuteincrements.
•Energy-savingratecanbesettoavaluefrom0%or50to90%in10%increments.
Night setback* Use to make Night setback settings.
•Select"Yes"toenablethesetting,and"No"todisablethesetting.Thetemperaturerangeandthestart/stoptimescanbeset.
Filter information Use to check the lter status.
•Theltersigncanbereset.
Error information Use to check error information when an error occurs.
•Checkcode,errorsource,refrigerantaddress,unitmodel,manufacturingnumber,contactinformation(dealer's
phonenumber)canbedisplayed.
(Theunitmodel,manufacturingnumber,andcontactinformationneedtoberegisteredinadvancetobedisplayed.)
Maintenance Auto descending panel Auto descending panel (Optional parts) Up / Down you can do.
Manual vane angle Use to set the vane angle for each vane to a xed position.
Initial setting Main/Sub When connecting two remote controllers, one of them needs to be designated as a sub controller.
Clock Use to set the current time.
Main display Use to switch between "Full" and "Basic" modes for the Main display.
•Theinitialsettingis"Full."
Contrast Use to adjust screen contrast.
Display details Make the settings for the remote controller related items as necessary.
Clock: Theinitialsettingsare"Yes"and"24h"format.
Temperature: SeteitherCelsius(°C)orFahrenheit(°F).
Room temp. : SetShoworHide.
Auto mode: SettheAutomodedisplayorOnlyAutodisplay.
Auto mode Whether or not to use the Auto mode can be selected by using the button.
This setting is valid only when indoor units with the Auto mode function are connected.
Administrator password The administrator password is required to make the settings for the following items.
•Timersetting•Energy-savesetting•Weeklytimersetting
•Restrictionsetting•Outdoorunitsilentmodesetting•Nightsetback
Language selection Use to select the desired language.
Service Test run Select "Test run" from the Service menu to bring up the Test run menu.
•Testrun•Drainpumptestrun
Input maintenance Select "Input maintenance Info." from the Service menu to bring up the Maintenance information screen.
The following settings can be made from the Maintenance Information screen.
•Modelnameinput•SerialNo.input•Dealerinformationinput
Function setting Make the settings for the indoor unit functions via the remote controller as necessary.
Check Error history: Displaytheerrorhistoryandexecute“deleteerrorhistory”.
Refrigerant leak check: Refrigerantleakscanbejudged.
Smooth maintenance: Theindoorandoutdoormaintenancedatacanbedisplayed.
Request code: Detailsoftheoperationdataincludingeachthermistortemperatureanderrorhistorycanbechecked.
Self check Error history of each unit can be checked via the remote controller.
Maintenance password Use to change the maintenance password.
Remote controller check When the remote controller does not work properly, use the remote controller checking function to trouble-
shoot the problem.
Main menu list
*Clocksettingisrequired.
OCH577A