Mitsubishi PUZ-A18NHA6 - Functions by Unit Number (01-03, AL)

96
Function Settings
Mode No.
No.
Setting
: Initial setting
(
Factory setting
)
- : Not available
4-Way
cassette
Ceiling
suspended
Wall mounted
PCA-KA PKA-HA(L) PKA-KA(L)
Filter sign
100h
1
2500h
07
(107)
2
"Clean the filter" indicator is not displayed
3
Air flow
Quiet
1 -
(
Fan speed
)
Standard
08
(108)
2
High ceiling
3
No.of air outlets
4 directions
1 - -
3 directions
09
(109)
2 - -
2 directions
3 - -
Optional high efficiency
Not supported
10
(110)
1
-
filter
Supported
2
-
Vane setting
No vanes (Vane No.3 setting : PLA only)
1 -
Vane No.1 setting
11
(111)
2 -
Vane No.2 setting
3 -
Optional humidifier
Not supported
13
(113)
1
- -
(
PLA only
)
Supported
2
- -
Vane differential setting
No.1 setting (TH5:
75-82°F ( 24-28:))
1
in heating mode
No.2 setting (Standard, TH5: 82-90°F (28-32:))
14
(114)
2
(
cold wind prevention
)
No.3 setting (TH5: 90-100
°F ( 32-38:))
3
Swing
23
(123)
1
2
Set temperature in heating
24
(124)
1
mode
(
4 deg up
) *1
2
Fan speed when the
Extra low
1
heating thermostat is OFF
Stop
25
(125)
2
Keeping fan speed set by remote controller
3
Fan speed when the
Keeping fan speed set by remote controller
27
(127)
1
cooling thermostat is OFF
Stop
2
Detection of abnormality of
Detect
28
(128)
1
the pipe temperature
(
P8
)
*1. PKA-HA(L)/KA(L): 3.6°F (2°C) up.
Neglect
2
-
-
-
-
-
-
-
-
-
-
-
PLA-BA
Not available Swing
Available Wave air flow
Available
Not available
}
PLA-BA
Wired remote controller
(RF thermistor)
(2)Functionsavailablewhensettingtheunitnumberto01-03orAL(07incaseofIRwirelessremotecontroller)
•Whensettingfunctionsforanindoorunitinanindependentsystem,settheunitnumberto01referringto4settingthe
indoorunitnumber.
•Whensettingfunctionsforasimultaneoustwinindoorunitsystem,settheunitnumberto01to03foreachindoorunitin
caseofselectingdifferentfunctionsforeachunitreferringto4settingtheindoorunitnumber.
•WhensettingthesamefunctionsforanentiresimultaneousTwin-indoorunitsystem,setrefrigerantaddresstoAL(07in
caseofIRwirelessremotecontroller)referringto4settingtheindoorunitnumber.
Mode No.11
Setting No. Settings PLA-BA PCA-KA
1
No Vanes
Vane No.3 setting
(
Downward position than the standard
)
Less smudging
No vane function
2 Vane No.1 setting
Standard
Standard
3 Vane No.2 setting
(
Upward position than the standard
)
Less draft *
(
Upward position than the standard
)
Less draft *
* Be careful of the smudge on ceiling.
Wired remote controller
(RF thermistor)
Wired remote controller
Function Settings
Mode No.
No.
Setting
: Initial setting
(
Factory setting
)
Filter sign 100h 1
2500h
07
(107)
2
No filter sign indicator
3
External static pressure
35/50/70/100/125Pa
08
(108)
10
(110)
1
2
Extra low
3
Fan speed during the
heating thermo OFF
Stop
25
(125)
1
Set fan speed
2
27
(127)
1
2
Detection of abnormality
of the pipe temperature (P8)
1
28
(128)
2
Set temperature in heating
24
(124)
mode
(
4 deg up
)
Refer to the right table
Refer to the right table
Available
Not available
Fan speed during the
cooling thermo OFF
Set fan speed
Stop
Available
Not available
External static
pressure
Setting No.
Initial setting
(
Factory setting
)
35Pa
50Pa
70Pa
100Pa
125Pa
2
3
1
2
3
Mode No.
8 (108)
1
1
2
2
2
10 (110)
PEAD-AA
OCH577A